|
1
|
[17:05:40.980]###########critical_process_check,485############
|
|
2
|
[17:05:45.999]###########critical_process_check,485############
|
|
3
|
[17:05:49.124]dying gasp
|
|
4
|
[17:05:51.512]
|
|
5
|
[17:05:51.512]
|
|
6
|
[17:05:51.513]U-Boot 2022.07 (Feb 27 2025 - 11:23:13 +0800) for emei
|
|
7
|
[17:05:51.513]
|
|
8
|
[17:05:51.513]DRAM: 256 MiB
|
|
9
|
[17:05:51.646]Core: 68 devices, 17 uclasses, devicetree: separate
|
|
10
|
[17:05:51.646]WDT: Started watchdog with servicing (30s timeout)
|
|
11
|
[17:05:51.693]NAND: 256 MiB
|
|
12
|
[17:05:52.007]Loading Environment from NAND... OK
|
|
13
|
[17:05:52.007]In: uart@0x1010f000
|
|
14
|
[17:05:52.007]Out: uart@0x1010f000
|
|
15
|
[17:05:52.007]Err: uart@0x1010f000
|
|
16
|
[17:05:52.068]Hard Power-on reset for internal POR circuit timing
|
|
17
|
[17:05:52.401]Net: Could not get PHY for eth6: addr 1
|
|
18
|
[17:05:52.402]hsan_mac gemac@0: gemac@0 no phy device
|
|
19
|
[17:05:52.869]Could not get PHY for eth7: addr 1
|
|
20
|
[17:05:52.869]hsan_mac gemac@8: gemac@8 no phy device
|
|
21
|
[17:05:52.869]eth0: pie
|
|
22
|
[17:05:52.896]bootflag b bootreg 0
|
|
23
|
[17:05:52.896]bootreg init, set 11
|
|
24
|
[17:06:01.127]Hit any key to stop autoboot: 0
|
|
25
|
[17:06:01.887]Reading 6291456 byte(s) (3072 page(s)) at offset 0x00000000
|
|
26
|
[17:06:02.512]bootreg offset: c08
|
|
27
|
[17:06:02.512]boot regval: 11
|
|
28
|
[17:06:02.512] Image Name: Linux-5.10.0
|
|
29
|
[17:06:02.512] Image Type: ARM Linux Kernel Image (uncompressed)
|
|
30
|
[17:06:02.526] Data Size: 6091416 Bytes = 5.8 MiB
|
|
31
|
[17:06:02.530] Load Address: 80208000
|
|
32
|
[17:06:02.530] Entry Point: 80208000
|
|
33
|
[17:06:02.909]alias console=/uart@0x1010f000
|
|
34
|
[17:06:02.909]serialnr->high=0x8250, serialnr->low=0x1010f000, atag_addr=0x80200100
|
|
35
|
[17:06:05.978]Uncompressing Linux... done, booting the kernel.
|
|
36
|
[17:06:06.070]Booting Linux on physical CPU 0x0
|
|
37
|
[17:06:06.070]Linux version 5.10.0 (ply@ubuntu22.04) (arm-mix510-linux-gcc (musl-1.2.3 linux-5.10 V12CS61.003.020 2024-01-16 12:00:00) 10.3.0, GNU ld (GNU Binutils) 2.38) #2 SMP Mon May 12 11:22:40 CST 2025
|
|
38
|
[17:06:06.071]CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=18c5387d
|
|
39
|
[17:06:06.071]CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
|
|
40
|
[17:06:06.071]OF: fdt: Machine model: hsan-emei
|
|
41
|
[17:06:06.071]OF: fdt: Ignoring memory range 0x80000000 - 0x80200000
|
|
42
|
[17:06:06.071]earlycon: uart0 at MMIO 0x1010f000 (options '')
|
|
43
|
[17:06:06.071]printk: bootconsole [uart0] enabled
|
|
44
|
[17:06:06.071]Memory policy: Data cache writealloc
|
|
45
|
[17:06:06.072]Zone ranges:
|
|
46
|
[17:06:06.072] Normal [mem 0x0000000080200000-0x000000009fffffff]
|
|
47
|
[17:06:06.072]Movable zone start for each node
|
|
48
|
[17:06:06.072]Early memory node ranges
|
|
49
|
[17:06:06.072] node 0: [mem 0x0000000080200000-0x00000000874fffff]
|
|
50
|
[17:06:06.072] node 0: [mem 0x0000000088000000-0x00000000888fffff]
|
|
51
|
[17:06:06.072] node 0: [mem 0x0000000088a00000-0x000000009fffffff]
|
|
52
|
[17:06:06.087]Zeroed struct page in unavailable ranges: 1024 pages
|
|
53
|
[17:06:06.087]Initmem setup node 0 [mem 0x0000000080200000-0x000000009fffffff]
|
|
54
|
[17:06:06.126]mdesc->l2c_aux_val 430001 mdesc->l2c_aux_mask ffb0fffe
|
|
55
|
[17:06:06.126]percpu: Embedded 20 pages/cpu s50636 r8192 d23092 u81920
|
|
56
|
[17:06:06.127]Built 1 zonelists, mobility grouping on. Total pages: 126340
|
|
57
|
[17:06:06.127]Kernel command line: noinitrd cma=0 console=ttyS0,115200 earlycon maxcpus=2 nr_cpus=2 additional_cpus=1
|
|
58
|
[17:06:06.127]Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
|
|
59
|
[17:06:06.141]Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
|
|
60
|
[17:06:06.142]mem auto-init: stack:off, heap alloc:off, heap free:off
|
|
61
|
[17:06:06.440]Memory: 488280K/509952K available (9494K kernel code, 1445K rwdata, 2972K rodata, 1720K init, 551K bss, 21672K reserved, 0K cma-reserved)
|
|
62
|
[17:06:06.440]SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
|
|
63
|
[17:06:06.440]rcu: Hierarchical RCU implementation.
|
|
64
|
[17:06:06.440] Tracing variant of Tasks RCU enabled.
|
|
65
|
[17:06:06.440]rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
|
|
66
|
[17:06:06.440]NR_IRQS: 16, nr_irqs: 192, preallocated irqs: 192
|
|
67
|
[17:06:06.441]L2C: platform modifies aux control register: 0x02030000 -> 0x02430001
|
|
68
|
[17:06:06.441]L2C: DT/platform modifies aux control register: 0x02030000 -> 0x02430001
|
|
69
|
[17:06:06.441]L2C: DT/platform tries to modify or specify cache size
|
|
70
|
[17:06:06.441]L2C-310 erratum 769419 enabled
|
|
71
|
[17:06:06.441]L2C-310 enabling early BRESP for Cortex-A9
|
|
72
|
[17:06:06.441]L2C-310: enabling full line of zeros but not enabled in Cortex-A9
|
|
73
|
[17:06:06.442]L2C-310 dynamic clock gating enabled, standby mode enabled
|
|
74
|
[17:06:06.442]L2C-310 cache controller enabled, 16 ways, 256 kB
|
|
75
|
[17:06:06.442]L2C-310: CACHE_ID 0x410000c9, AUX_CTRL 0x46430001
|
|
76
|
[17:06:06.442]random: get_random_bytes called from start_kernel+0x380/0x578 with crng_init=0
|
|
77
|
[17:06:06.442]clocksource: arm,sp804: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604467 ns
|
|
78
|
[17:06:06.442]sched_clock: 32 bits at 100MHz, resolution 10ns, wraps every 21474836475ns
|
|
79
|
[17:06:06.442]sched_clock: 64 bits at 200MHz, resolution 5ns, wraps every 4398046511102ns
|
|
80
|
[17:06:06.443]clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x2e2049d3e8, max_idle_ns: 440795210634 ns
|
|
81
|
[17:06:06.443]Switching to timer-based delay loop, resolution 5ns
|
|
82
|
[17:06:06.443]Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000)
|
|
83
|
[17:06:06.443]pid_max: default: 32768 minimum: 301
|
|
84
|
[17:06:06.443]Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
|
|
85
|
[17:06:06.443]Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
|
|
86
|
[17:06:06.443]CPU: Testing write buffer coherency: ok
|
|
87
|
[17:06:06.443]CPU0: Spectre v2: using BPIALL workaround
|
|
88
|
[17:06:06.443]CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
|
|
89
|
[17:06:06.443]Setting up static identity map for 0x80208220 - 0x80208280
|
|
90
|
[17:06:06.443]rcu: Hierarchical SRCU implementation.
|
|
91
|
[17:06:06.443]smp: Bringing up secondary CPUs ...
|
|
92
|
[17:06:06.443]CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
|
|
93
|
[17:06:06.443]CPU1: Spectre v2: using BPIALL workaround
|
|
94
|
[17:06:06.444]smp: Brought up 1 node, 2 CPUs
|
|
95
|
[17:06:06.444]SMP: Total of 2 processors activated (800.00 BogoMIPS).
|
|
96
|
[17:06:06.444]CPU: All CPU(s) started in SVC mode.
|
|
97
|
[17:06:06.445]allocated 524288 bytes of page_ext
|
|
98
|
[17:06:06.445]devtmpfs: initialized
|
|
99
|
[17:06:06.451]clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
|
|
100
|
[17:06:06.451]futex hash table entries: 512 (order: 3, 32768 bytes, linear)
|
|
101
|
[17:06:06.451]pinctrl core: initialized pinctrl subsystem
|
|
102
|
[17:06:06.452]NET: Registered protocol family 16
|
|
103
|
[17:06:06.452]DMA: preallocated 256 KiB pool for atomic coherent allocations
|
|
104
|
[17:06:06.452]thermal_sys: Registered thermal governor 'fair_share'
|
|
105
|
[17:06:06.453]thermal_sys: Registered thermal governor 'bang_bang'
|
|
106
|
[17:06:06.453]thermal_sys: Registered thermal governor 'step_wise'
|
|
107
|
[17:06:06.453]thermal_sys: Registered thermal governor 'user_space'
|
|
108
|
[17:06:06.453]thermal_sys: Registered thermal governor 'power_allocator'
|
|
109
|
[17:06:06.453]hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
|
|
110
|
[17:06:06.453]hw-breakpoint: maximum watchpoint size is 4 bytes.
|
|
111
|
[17:06:06.453]Serial: AMBA PL011 UART driver
|
|
112
|
[17:06:06.478]OF: /gpio@0x10106000/gpio-port@0: could not get #gpio-cells for /mii_misc@0
|
|
113
|
[17:06:06.478]OF: /gpio@0x10107000/gpio-port@0: could not get #gpio-cells for /mdio0/ethernet-phy@1
|
|
114
|
[17:06:06.497]SCSI subsystem initialized
|
|
115
|
[17:06:06.497]usbcore: registered new interface driver usbfs
|
|
116
|
[17:06:06.497]usbcore: registered new interface driver hub
|
|
117
|
[17:06:06.497]usbcore: registered new device driver usb
|
|
118
|
[17:06:06.497]NET: Registered protocol family 8
|
|
119
|
[17:06:06.497]NET: Registered protocol family 20
|
|
120
|
[17:06:06.513]clocksource: Switched to clocksource arm_global_timer
|
|
121
|
[17:06:06.749]VFS: Disk quotas dquot_6.6.0
|
|
122
|
[17:06:06.750]VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
|
|
123
|
[17:06:06.750]FS-Cache: Loaded
|
|
124
|
[17:06:06.750]CacheFiles: Loaded
|
|
125
|
[17:06:06.750]NET: Registered protocol family 2
|
|
126
|
[17:06:06.750]tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
|
|
127
|
[17:06:06.751]TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
|
|
128
|
[17:06:06.751]TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear)
|
|
129
|
[17:06:06.751]TCP: Hash tables configured (established 4096 bind 4096)
|
|
130
|
[17:06:06.751]UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
|
|
131
|
[17:06:06.751]UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
|
|
132
|
[17:06:06.752]NET: Registered protocol family 1
|
|
133
|
[17:06:06.752]RPC: Registered named UNIX socket transport module.
|
|
134
|
[17:06:06.752]RPC: Registered udp transport module.
|
|
135
|
[17:06:06.752]RPC: Registered tcp transport module.
|
|
136
|
[17:06:06.757]RPC: Registered tcp NFSv4.1 backchannel transport module.
|
|
137
|
[17:06:06.757]NET: Registered protocol family 44
|
|
138
|
[17:06:06.757]PCI: CLS 0 bytes, default 64
|
|
139
|
[17:06:06.878]Initialise system trusted keyrings
|
|
140
|
[17:06:06.878]workingset: timestamp_bits=14 max_order=17 bucket_order=3
|
|
141
|
[17:06:06.878]squashfs: version 4.0 (2009/01/31) Phillip Lougher
|
|
142
|
[17:06:06.878]ntfs: driver 2.1.32 [Flags: R/W DEBUG].
|
|
143
|
[17:06:06.878]jffs2: version 2.2. (NAND) (SUMMARY) ? 2001-2006 Red Hat, Inc.
|
|
144
|
[17:06:06.889]fuse: init (API version 7.32)
|
|
145
|
[17:06:07.219]Key type asymmetric registered
|
|
146
|
[17:06:07.220]Asymmetric key parser 'x509' registered
|
|
147
|
[17:06:07.220]Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
|
|
148
|
[17:06:07.220]Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
|
|
149
|
[17:06:07.220]printk: console [ttyS0] disabled
|
|
150
|
[17:06:07.220]1010f000.uart: ttyS0 at MMIO 0x1010f000 (irq = 205, base_baud = 6250000) is a 16550A
|
|
151
|
[17:06:07.220]printk: console [ttyS0] enabled
|
|
152
|
[17:06:07.221]printk: console [ttyS0] enabled
|
|
153
|
[17:06:07.221]printk: bootconsole [uart0] disabled
|
|
154
|
[17:06:07.221]printk: bootconsole [uart0] disabled
|
|
155
|
[17:06:07.221]libphy: Fixed MDIO Bus: probed
|
|
156
|
[17:06:07.221]PPP generic driver version 2.4.2
|
|
157
|
[17:06:07.221]PPP MPPE Compression module registered
|
|
158
|
[17:06:07.221]NET: Registered protocol family 24
|
|
159
|
[17:06:07.222]SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
|
|
160
|
[17:06:07.222]CSLIP: code copyright 1989 Regents of the University of California.
|
|
161
|
[17:06:07.222]SLIP linefill/keepalive option.
|
|
162
|
[17:06:07.222]usbcore: registered new interface driver uas
|
|
163
|
[17:06:07.222]usbcore: registered new interface driver usb-storage
|
|
164
|
[17:06:07.222]usbcore: registered new interface driver usbserial_generic
|
|
165
|
[17:06:07.222]usbserial: USB Serial support registered for generic
|
|
166
|
[17:06:07.223]usbcore: registered new interface driver ch341
|
|
167
|
[17:06:07.223]usbserial: USB Serial support registered for ch341-uart
|
|
168
|
[17:06:07.223]usbcore: registered new interface driver cp210x
|
|
169
|
[17:06:07.223]usbserial: USB Serial support registered for cp210x
|
|
170
|
[17:06:07.223]usbcore: registered new interface driver ftdi_sio
|
|
171
|
[17:06:07.223]usbserial: USB Serial support registered for FTDI USB Serial Device
|
|
172
|
[17:06:07.223]usbcore: registered new interface driver pl2303
|
|
173
|
[17:06:07.224]usbserial: USB Serial support registered for pl2303
|
|
174
|
[17:06:07.224]GACT probability NOT on
|
|
175
|
[17:06:07.224]Mirror/redirect action on
|
|
176
|
[17:06:07.224]u32 classifier
|
|
177
|
[17:06:07.224] input device check on
|
|
178
|
[17:06:07.224] Actions configured
|
|
179
|
[17:06:07.224]xt_time: kernel timezone is -0000
|
|
180
|
[17:06:07.224]ipip: IPv4 and MPLS over IPv4 tunneling driver
|
|
181
|
[17:06:07.224]Initializing XFRM netlink socket
|
|
182
|
[17:06:07.225]NET: Registered protocol family 10
|
|
183
|
[17:06:07.229]Segment Routing with IPv6
|
|
184
|
[17:06:07.229]sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
|
|
185
|
[17:06:07.229]NET: Registered protocol family 17
|
|
186
|
[17:06:07.229]Bridge firewalling registered
|
|
187
|
[17:06:07.229]l2tp_core: L2TP core driver, V2.0
|
|
188
|
[17:06:07.229]l2tp_ppp: PPPoL2TP kernel driver, V2.0
|
|
189
|
[17:06:07.230]l2tp_ip: L2TP IP encapsulation support (L2TPv3)
|
|
190
|
[17:06:07.230]l2tp_netlink: L2TP netlink interface
|
|
191
|
[17:06:07.230]l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
|
|
192
|
[17:06:07.230]l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
|
|
193
|
[17:06:07.230]8021q: 802.1Q VLAN Support v1.8
|
|
194
|
[17:06:07.230]lib80211: common routines for IEEE802.11 drivers
|
|
195
|
[17:06:07.230]Registering SWP/SWPB emulation handler
|
|
196
|
[17:06:07.230]Loading compiled-in X.509 certificates
|
|
197
|
[17:06:07.231]cfg80211: Loading compiled-in X.509 certificates for regulatory database
|
|
198
|
[17:06:07.231]cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
|
|
199
|
[17:06:07.231]platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
|
|
200
|
[17:06:07.231]Warning: unable to open an initial console.
|
|
201
|
[17:06:07.231]cfg80211: failed to load regulatory.db
|
|
202
|
[17:06:07.231]Freeing unused kernel memory: 1720K
|
|
203
|
[17:06:07.237]Kernel memory protection not selected by kernel config.
|
|
204
|
[17:06:07.238]Run /init as init process
|
|
205
|
[17:06:07.271]hi_crg: loading out-of-tree module taints kernel.
|
|
206
|
[17:06:07.304][DFX]
|
|
207
|
[17:06:07.304] HSAN mlog_print function is unavailable...
|
|
208
|
[17:06:07.305]Basic driver of Linux Kernel install successfully ...!
|
|
209
|
[17:06:07.333]1010e000.uart: ttyS1 at MMIO 0x1010e000 (irq = 206, base_baud = 6250000) is a 16550A
|
|
210
|
[17:06:07.362]hi-reset reset@0: resister reset device
|
|
211
|
[17:06:07.362]hi-reset reset@1: resister reset device
|
|
212
|
[17:06:07.362]hi-reset reset@2: resister reset device
|
|
213
|
[17:06:07.382]10a40000.usb_ehci_acp : ON
|
|
214
|
[17:06:07.382]10600000.usb_xhci_acp : ON
|
|
215
|
[17:06:07.382]10160000.pcie_acp : OFF
|
|
216
|
[17:06:07.382]10164000.pcie_acp : OFF
|
|
217
|
[17:06:07.394]10a70000.pie_acp : ON
|
|
218
|
[17:06:07.395]hsan-watchdog-driver 14880000.watchdog: Hsan watchdog timeout=30 sec, nowayout=1
|
|
219
|
[17:06:07.532]HSAN FMC Controller Device Driver, Version 100
|
|
220
|
[17:06:07.532]15 fixed-partitions partitions found on MTD device 10a20000.fmc
|
|
221
|
[17:06:07.532]Creating 15 MTD partitions on "10a20000.fmc":
|
|
222
|
[17:06:07.532]0x000000000000-0x000000100000 : "uboot"
|
|
223
|
[17:06:07.532]0x000000100000-0x000000140000 : "enva"
|
|
224
|
[17:06:07.532]0x000000140000-0x000000180000 : "envb"
|
|
225
|
[17:06:07.533]0x000000180000-0x000000380000 : "fac"
|
|
226
|
[17:06:07.533]0x000000380000-0x000000580000 : "cfga"
|
|
227
|
[17:06:07.533]0x000000580000-0x000000780000 : "cfgb"
|
|
228
|
[17:06:07.533]0x000000780000-0x000000c40000 : "log"
|
|
229
|
[17:06:07.533]0x000000c40000-0x000000c80000 : "pstore"
|
|
230
|
[17:06:07.533]0x000000c80000-0x000001280000 : "kernela"
|
|
231
|
[17:06:07.533]0x000001280000-0x000001880000 : "kernelb"
|
|
232
|
[17:06:07.533]0x000001880000-0x000006080000 : "rootfsa"
|
|
233
|
[17:06:07.546]0x000006080000-0x00000a880000 : "rootfsb"
|
|
234
|
[17:06:07.546]0x00000a880000-0x00000b880000 : "fwka"
|
|
235
|
[17:06:07.546]0x00000b880000-0x00000c880000 : "fwkb"
|
|
236
|
[17:06:07.589]0x00000c880000-0x000010000000 : "app"
|
|
237
|
[17:06:07.589]show boot_reg: 10
|
|
238
|
[17:06:07.619]ubi0: attaching mtd11
|
|
239
|
[17:06:07.787]ubi0: scanning is finished
|
|
240
|
[17:06:07.787]ubi0 error: ubi_read_volume_table [ubi]: the layout volume was not found
|
|
241
|
[17:06:07.806]ubi0 error: ubi_attach_mtd_dev [ubi]: failed to attach mtd11, error -22
|
|
242
|
[17:06:07.806]UBI error: cannot attach mtd11
|
|
243
|
[17:06:07.806]UBI error: cannot initialize UBI, error -22
|
|
244
|
[17:06:13.468]
|
|
245
|
[17:06:13.469]pie module commit_id:1195a7f5
|
|
246
|
[17:06:13.469]
|
|
247
|
[17:06:13.469]clipper module commit_id:1195a7f5
|
|
248
|
[17:06:13.469]pie 10a70000.pie: open dma-coherent 3000000
|
|
249
|
[17:06:13.469]pie 10a70000.pie: Hisilicon pie swver=v210,hwver=v200
|
|
250
|
[17:06:13.469]
|
|
251
|
[17:06:13.470]mdio module commit_id:1195a7f5
|
|
252
|
[17:06:13.470]libphy: hi_mii_bus: probed
|
|
253
|
[17:06:13.470]
|
|
254
|
[17:06:13.470]phy module commit_id:1195a7f5
|
|
255
|
[17:06:13.470][GEPHY]Genius Phy hwVer:0x20669a0e fwVer:0x6807
|
|
256
|
[17:06:13.470]
|
|
257
|
[17:06:13.470]phy module commit_id:1195a7f5
|
|
258
|
[17:06:13.470]
|
|
259
|
[17:06:13.470]phy module commit_id:1195a7f5
|
|
260
|
[17:06:13.470]
|
|
261
|
[17:06:13.470]phy module commit_id:1195a7f5
|
|
262
|
[17:06:13.470]
|
|
263
|
[17:06:13.470]mac module commit_id:1195a7f5
|
|
264
|
[17:06:13.470]
|
|
265
|
[17:06:13.471]mac module commit_id:1195a7f5
|
|
266
|
[17:06:13.471]
|
|
267
|
[17:06:13.471]mac module commit_id:1195a7f5
|
|
268
|
[17:06:13.471]
|
|
269
|
[17:06:13.471]mac module commit_id:1195a7f5
|
|
270
|
[17:06:13.471]
|
|
271
|
[17:06:13.471]misc module commit_id:1195a7f5
|
|
272
|
[17:06:13.471]mii_misc 14890138.mii_misc: Hisilicon mii misc driver init
|
|
273
|
[17:06:13.471]
|
|
274
|
[17:06:13.471]pcs module commit_id:1195a7f5
|
|
275
|
[17:06:13.471]pcs 14e00000.pcs: Hisilicon pcs driver init
|
|
276
|
[17:06:13.471]
|
|
277
|
[17:06:13.472]team module commit_id:1195a7f5
|
|
278
|
[17:06:13.472]
|
|
279
|
[17:06:13.487]
|
|
280
|
[17:06:13.487]lsw module commit_id:1195a7f5
|
|
281
|
[17:06:13.487]
|
|
282
|
[17:06:13.493]
|
|
283
|
[17:06:13.493]dp module commit_id:1195a7f5
|
|
284
|
[17:06:13.493]
|
|
285
|
[17:06:13.493]failed to find hsan,queue_reserved node
|
|
286
|
[17:06:13.493]failed to find hsan,flow_reserved node
|
|
287
|
[17:06:13.500][LSW]Hisilicon lsw dp swver=v300,hwver=v200,ret=0x0
|
|
288
|
[17:06:13.545]
|
|
289
|
[17:06:13.545]pfe module commit_id:1195a7f5
|
|
290
|
[17:06:13.545]
|
|
291
|
[17:06:13.577][LSW]Hisilicon lsw pfe swver=v200,hwver=v200,ret=0x0
|
|
292
|
[17:06:13.620]
|
|
293
|
[17:06:13.621]cfe pub module commit_id:4319684c
|
|
294
|
[17:06:13.621][CFE]CFE PUB module install successfully ...!
|
|
295
|
[17:06:13.720]
|
|
296
|
[17:06:13.721]cfe lrn module commit_id:4319684c
|
|
297
|
[17:06:13.722][CFE]CFE LRN module install successfully ...!
|
|
298
|
[17:06:13.722]
|
|
299
|
[17:06:13.722]l3 lib module commit_id:4319684c
|
|
300
|
[17:06:13.722][CFE]L3 LIB module install successfully ...!
|
|
301
|
[17:06:13.722]
|
|
302
|
[17:06:13.722]l4 lib module commit_id:4319684c
|
|
303
|
[17:06:13.723][CFE]L4 LIB module install successfully ...!
|
|
304
|
[17:06:13.723]
|
|
305
|
[17:06:13.723]l2tp lib module commit_id:4319684c
|
|
306
|
[17:06:13.723][CFE]L2TP LIB module install successfully ...!
|
|
307
|
[17:06:13.723]
|
|
308
|
[17:06:13.724]dslite lib module commit_id:4319684c
|
|
309
|
[17:06:13.724][CFE]DSLITE LIB module install successfully ...!
|
|
310
|
[17:06:13.724]
|
|
311
|
[17:06:13.724]mc lib module commit_id:4319684c
|
|
312
|
[17:06:13.724][CFE]MC LIB module install successfully ...!
|
|
313
|
[17:06:13.724]
|
|
314
|
[17:06:13.724]mc list module commit_id:4319684c
|
|
315
|
[17:06:13.725][CFE]MC LIST module install successfully ...!
|
|
316
|
[17:06:13.725]
|
|
317
|
[17:06:13.725]vxlan lib module commit_id:4319684c
|
|
318
|
[17:06:13.754][CFE]VXLAN LIB module install successfully ...!
|
|
319
|
[17:06:13.754]
|
|
320
|
[17:06:13.754]cfe adp capa module commit_id:4319684c
|
|
321
|
[17:06:13.788]
|
|
322
|
[17:06:13.788]hslink module commit_id:4319684c
|
|
323
|
[17:06:13.788][HSLINK]HSLINK install successfully ...!
|
|
324
|
[17:06:13.788]
|
|
325
|
[17:06:13.788]serdes module commit_id:1195a7f5
|
|
326
|
[17:06:13.788]
|
|
327
|
[17:06:13.864]i2c /dev entries driver
|
|
328
|
[17:06:13.894]
|
|
329
|
[17:06:13.894]pon_core module commit_id:1195a7f5
|
|
330
|
[17:06:13.894]
|
|
331
|
[17:06:13.894]
|
|
332
|
[17:06:13.894][PON]pon_core module install succ!
|
|
333
|
[17:06:13.917]
|
|
334
|
[17:06:13.918]ploam module commit_id:1195a7f5
|
|
335
|
[17:06:13.918]
|
|
336
|
[17:06:13.918][PON]pon_ploam module install succ!
|
|
337
|
[17:06:13.918]
|
|
338
|
[17:06:13.918]pon_glb module commit_id:1195a7f5
|
|
339
|
[17:06:13.918]
|
|
340
|
[17:06:13.924]pon optical module tx en level [0]
|
|
341
|
[17:06:13.924]pon optical module rx los level [0]
|
|
342
|
[17:06:13.924][PON]pon_global module install succ!
|
|
343
|
[17:06:13.964]
|
|
344
|
[17:06:13.964]gmac module commit_id:1195a7f5
|
|
345
|
[17:06:13.964]
|
|
346
|
[17:06:13.964][PON]pon_gmac module install succ!
|
|
347
|
[17:06:13.964]
|
|
348
|
[17:06:13.964]emac module commit_id:1195a7f5
|
|
349
|
[17:06:13.964]
|
|
350
|
[17:06:13.972][PON]pon_emac module install succ!
|
|
351
|
[17:06:14.031]
|
|
352
|
[17:06:14.031]mpcp module commit_id:1195a7f5
|
|
353
|
[17:06:14.031]
|
|
354
|
[17:06:14.031][PON]pon_mpcp module install succ!
|
|
355
|
[17:06:14.049]dw-apb-uart 1010f000.uart: forbid DMA for kernel console
|
|
356
|
[17:06:14.049]mount file system start
|
|
357
|
[17:06:15.235]Changing password for root
|
|
358
|
[17:06:15.236]New password:
|
|
359
|
[17:06:15.236]Bad password: too weak
|
|
360
|
[17:06:15.236]Retype password:
|
|
361
|
[17:06:15.256]passwd: password for root changed by root
|
|
362
|
[17:06:15.256]mount file system end
|
|
363
|
[17:06:16.040]permission adapt start
|
|
364
|
[17:06:18.070]permission adapt endmodule rootkit_infection_detection init success. kln_address=c00be93c
|
|
365
|
[17:06:18.082]The board info is vendor_id=hsan, chip_id=emei, board_id=0(0x0)
|
|
366
|
[17:06:18.083]The board.xml is exist, keep old board.xml
|
|
367
|
[17:06:18.083]init board
|
|
368
|
[17:06:18.143]sysctl_conf start
|
|
369
|
[17:06:18.143]sysctl_conf end
|
|
370
|
[17:06:18.143]ln /etc/localtime
|
|
371
|
[17:06:18.220][HI_APPM] ########### Appm Start Begin ###########
|
|
372
|
[17:06:18.247]appm init begin
|
|
373
|
[17:06:18.292]begin ctc_smart_prepare !!!
|
|
374
|
[17:06:18.292]
|
|
375
|
[17:06:18.292]gateway module commit_id:ffffffff
|
|
376
|
[17:06:18.292]
|
|
377
|
[17:06:18.292]
|
|
378
|
[17:06:18.292] hi_notify_init succ
|
|
379
|
[17:06:18.292]ubi0: attaching mtd14
|
|
380
|
[17:06:18.458]ubi0: scanning is finished
|
|
381
|
[17:06:18.511]ubi0: attached mtd14 (name "app", size 55 MiB)
|
|
382
|
[17:06:18.511]ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
|
|
383
|
[17:06:18.511]ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
|
|
384
|
[17:06:18.511]ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
|
|
385
|
[17:06:18.511]ubi0: good PEBs: 444, bad PEBs: 0, corrupted PEBs: 0
|
|
386
|
[17:06:18.511]ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
|
|
387
|
[17:06:18.512]ubi0: max/mean erase counter: 4/2, WL threshold: 4096, image sequence number: 3611534910
|
|
388
|
[17:06:18.520]ubi0: available PEBs: 0, total reserved PEBs: 444, PEBs reserved for bad PEB handling: 40
|
|
389
|
[17:06:18.520]ubi0: background thread "ubi_bgt0d" started, PID 631
|
|
390
|
[17:06:18.610]UBIFS (ubi0:0): Mounting in unauthenticated mode
|
|
391
|
[17:06:18.610]UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 642
|
|
392
|
[17:06:18.610]UBIFS (ubi0:0): recovery needed
|
|
393
|
[17:06:18.748]UBIFS (ubi0:0): recovery completed
|
|
394
|
[17:06:18.748]UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "app"
|
|
395
|
[17:06:18.748]UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
|
|
396
|
[17:06:18.748]UBIFS (ubi0:0): FS size: 49520640 bytes (47 MiB, 390 LEBs), journal size 2539520 bytes (2 MiB, 20 LEBs)
|
|
397
|
[17:06:18.749]UBIFS (ubi0:0): reserved for root: 2338982 bytes (2284 KiB)
|
|
398
|
[17:06:18.749]UBIFS (ubi0:0): media format: w5/r0 (latest is w5/r0), UUID FA3155A0-BDCE-47E7-B32B-650FA70D4042, small LPT model
|
|
399
|
[17:06:18.752]mount ctc app partition !!!
|
|
400
|
[17:06:18.789]MAXNET DPI interface Loaded
|
|
401
|
[17:06:18.789]mouting cgroup start!
|
|
402
|
[17:06:18.879]mouting cgroup finish!
|
|
403
|
[17:06:18.933]random: dbus-uuidgen: uninitialized urandom read (12 bytes read)
|
|
404
|
[17:06:18.938]random: dbus-uuidgen: uninitialized urandom read (8 bytes read)
|
|
405
|
[17:06:19.031]random: dbus-daemon: uninitialized urandom read (12 bytes read)
|
|
406
|
[17:06:19.066][HI_APPM] [succ] init script
|
|
407
|
[17:06:19.066][HI_APPM] [succ] init path
|
|
408
|
[17:06:19.067][HI_APPM] [succ] init lib
|
|
409
|
[17:06:19.075][HI_APPM] [succ] init app
|
|
410
|
[17:06:19.075][HI_APPM] [succ] init group
|
|
411
|
[17:06:19.075][smart] start ipc_service !!!
|
|
412
|
[17:06:19.124]cp: can't stat '/sbin/bpftool': No such file or directory
|
|
413
|
[17:06:19.124][smart] wait ipc_service init fin
|
|
414
|
[17:06:20.462][HI_IPC] ipc call hi_IPC_igdGetCmInitState_call fail, pid 2 ret 72200013, data0[6]
|
|
415
|
[17:06:20.491][HI_APPM] [succ] init db
|
|
416
|
[17:06:20.513][HI_APPM] [succ] new process(698)
|
|
417
|
[17:06:20.513][HI_APPM] [succ] <0> sysinfo
|
|
418
|
[17:06:20.525][HI_APPM] [succ] start sysinfo
|
|
419
|
[17:06:20.526][HI_APPM] [succ] new process(700)
|
|
420
|
[17:06:20.526][HI_APPM] [succ] <0> syslog
|
|
421
|
[17:06:20.596][HI_APPM] [succ] <1> crashlog
|
|
422
|
[17:06:20.597][HI_APPM] [succ] start syslog
|
|
423
|
[17:06:20.615][HI_APPM] [succ] new process(718)
|
|
424
|
[17:06:20.615][HI_APPM] [succ] <0> sysstat
|
|
425
|
[17:06:21.447][HI_APPM] [succ] <1> omdiag
|
|
426
|
[17:06:21.447][HI_APPM] [succ] start sysstat
|
|
427
|
[17:06:21.448][HI_APPM] [succ] new process(730)
|
|
428
|
[17:06:21.448][HI_APPM] [succ] <0> encrypt
|
|
429
|
[17:06:21.449][HI_APPM] [succ] start encrypt
|
|
430
|
[17:06:21.449][HI_APPM] [succ] new process(732)
|
|
431
|
[17:06:21.449][HI_IPC] ipc call hi_IPC_igdGetCmInitState_call fail, pid 2 ret 72200013, data0[6]
|
|
432
|
[17:06:21.453][HI_APPM] [succ] <0> board
|
|
433
|
[17:06:21.453]
|
|
434
|
[17:06:21.454]pon module install succ!
|
|
435
|
[17:06:21.481]xPON CtcOam V1.0 is installed!
|
|
436
|
[17:06:21.602]
|
|
437
|
[17:06:21.709] hi_vendor0_bob_init ok!
|
|
438
|
[17:06:21.709][HI_APPM] [succ] <1> bob
|
|
439
|
[17:06:21.709][HI_APPM] [succ] <2> optical
|
|
440
|
[17:06:21.709][HI_IPC] ipc call hi_hi_board_iomap_call_call fail, pid 732 ret 8ffffff2, data0[4]
|
|
441
|
[17:06:21.710][HI_IPC] ipc call hi_hi_board_iomap_call_call fail, pid 732 ret 8ffffff2, data0[5]
|
|
442
|
[17:06:21.710][HI_IPC] ipc call hi_hi_board_iomap_call_call fail, pid 732 ret 8ffffff2, data0[6]
|
|
443
|
[17:06:21.710][HI_IPC] ipc call hi_hi_board_iomap_call_call fail, pid 732 ret 8ffffff2, data0[7]
|
|
444
|
[17:06:21.710][HI_IPC] ipc call hi_hi_board_iomap_call_call fail, pid 732 ret 8ffffff2, data0[8]
|
|
445
|
[17:06:21.710][HI_IPC] ipc call hi_hi_board_iomap_call_call fail, pid 732 ret 8ffffff2, data0[9]
|
|
446
|
[17:06:21.710][HI_IPC] ipc call hi_hi_board_iomap_call_call fail, pid 732 ret 8ffffff2, data0[10]
|
|
447
|
[17:06:21.711][HI_IPC] ipc call hi_hi_board_iomap_call_call fail, pid 732 ret 8ffffff2, data0[11]
|
|
448
|
[17:06:21.711][HI_IPC] ipc call hi_hi_board_iomap_call_call fail, pid 732 ret 8ffffff2, data0[13]
|
|
449
|
[17:06:21.711][HI_IPC] ipc call hi_hi_board_iomap_call_call fail, pid 732 ret 8ffffff2, data0[14]
|
|
450
|
[17:06:21.711][LED]Led init suc!!! Led data num = 5
|
|
451
|
[17:06:21.711][LED]Failed to open gpiochip2 err=No such file or directory
|
|
452
|
[17:06:21.711][HI_APPM] [succ] <3> led
|
|
453
|
[17:06:21.712][HI_IPC] ipc call hi_hi_board_iomap_call_call fail, pid 732 ret 8ffffff2, data0[19]
|
|
454
|
[17:06:21.712][HI_IPC] ipc call hi_hi_board_iomap_call_call fail, pid 732 ret 8ffffff2, data0[19]
|
|
455
|
[17:06:21.723][HI_APPM] [succ] <4> key
|
|
456
|
[17:06:21.723][HI_APPM] [succ] start ext_dev
|
|
457
|
[17:06:21.723][HI_APPM] [succ] new process(741)
|
|
458
|
[17:06:21.764]url_init
|
|
459
|
[17:06:21.764]
|
|
460
|
[17:06:21.765]cfe xtables install succ!
|
|
461
|
[17:06:22.465][HI_IPC] ipc call hi_IPC_igdGetCmInitState_call fail, pid 2 ret 72200013, data0[6]
|
|
462
|
[17:06:22.465][WAN_ERR:hi_wan_port_attacth_netdev(334)]ifname vap20 port 20000000 not in global ports
|
|
463
|
[17:06:22.466][WAN_ERR:hi_wan_port_attacth_netdev(334)]ifname vap50 port 40000000 not in global ports
|
|
464
|
[17:06:22.477][WAN_ERR:hi_wan_port_attacth_netdev(334)]ifname mld2 port 80000000 not in global ports
|
|
465
|
[17:06:23.470][HI_IPC] ipc call hi_IPC_igdGetCmInitState_call fail, pid 2 ret 72200013, data0[6]
|
|
466
|
[17:06:24.009][HI_APPM] [succ] <0> wan
|
|
467
|
[17:06:24.038]insmod ra_bind succ!!
|
|
468
|
[17:06:24.267]lan init succ
|
|
469
|
[17:06:24.267][HI_APPM] [succ] <1> lan
|
|
470
|
[17:06:24.268]insmod vxlan succ!!
|
|
471
|
[17:06:24.445][HI_APPM] [succ] <2> vxlan
|
|
472
|
[17:06:24.445][HI_APPM] [succ] start wan_lan
|
|
473
|
[17:06:24.445][HI_APPM] [succ] new process(1062)
|
|
474
|
[17:06:24.446][HI_APPM] [succ] <0> wlan
|
|
475
|
[17:06:24.464][HI_IPC] ipc call hi_IPC_igdGetCmInitState_call fail, pid 2 ret 72200013, data0[6]
|
|
476
|
[17:06:24.464]insmod hostlimit succ!!
|
|
477
|
[17:06:24.731][HI_APPM] [succ] <1> lanhost
|
|
478
|
[17:06:24.731][HI_APPM] [succ] start host
|
|
479
|
[17:06:24.748][HI_APPM] [succ] new process(1106)
|
|
480
|
[17:06:24.748]hi_qos_init ui_nf_conntrack_max= 61000
|
|
481
|
[17:06:25.654][HI_IPC] ipc call hi_IPC_igdGetCmInitState_call fail, pid 2 ret 72200013, data0[6]
|
|
482
|
[17:06:25.958][HI_APPM] [succ] <0> qos
|
|
483
|
[17:06:25.990][HI_APPM] [succ] start qos
|
|
484
|
[17:06:25.990][HI_APPM] [succ] new process(1262)
|
|
485
|
[17:06:26.470][HI_IPC] ipc call hi_IPC_igdGetCmInitState_call fail, pid 2 ret 72200013, data0[6]
|
|
486
|
[17:06:26.848][HI_APPM] [succ] <0random: fast init done
|
|
487
|
[17:06:26.848]> sec
|
|
488
|
[17:06:27.471][HI_IPC] ipc call hi_IPC_igdGetCmInitState_call fail, pid 2 ret 72200013, data0[6]
|
|
489
|
[17:06:27.767][HI_IPC] ipc call hi_hi_vpn_check_tunn_name_call fail, pid 0 ret 72200013, data0[812151909]
|
|
490
|
[17:06:27.792][HI_IPC] ipc call hi_hi_vpn_check_tunn_name_call fail, pid 0 ret 72200013, data0[812151909]
|
|
491
|
[17:06:28.486][HI_IPC] ipc call hi_IPC_igdGetCmInitState_call fail, pid 2 ret 72200013, data0[6]
|
|
492
|
[17:06:28.693][HI_APPM] [succ] <1> netapp
|
|
493
|
[17:06:28.713][HI_APPM] [succ] <2> emu
|
|
494
|
[17:06:28.713][HI_APPM] [succ] start netapp
|
|
495
|
[17:06:28.724][HI_APPM] [succ] new process(1421)
|
|
496
|
[17:06:28.927][HI_APPM] [succ] <0> vpn
|
|
497
|
[17:06:28.927][HI_APPM] [succ] <1> upgrade
|
|
498
|
[17:06:28.927][HI_APPM] [succ] <2> download
|
|
499
|
[17:06:28.928][HI_APPM] [succ] <3> upload
|
|
500
|
[17:06:28.928][HI_APPM] [succ] start netservice
|
|
501
|
[17:06:28.937][HI_APPM] [succ] new process(1435)
|
|
502
|
[17:06:28.938][HI_APPM] [succ] <0> voip
|
|
503
|
[17:06:28.938][HI_APPM] [succ] <1> slic
|
|
504
|
[17:06:29.300]
|
|
505
|
[17:06:29.300]hisilicon kvoip module install succ!
|
|
506
|
[17:06:29.480][HI_IPC] ipc call hi_IPC_igdGetCmInitState_call fail, pid 2 ret 72200013, data0[6]
|
|
507
|
[17:06:29.508]zsp_min.out
|
|
508
|
[17:06:29.628][HI_APPM] [succ] <2> voice
|
|
509
|
[17:06:29.629][HI_APPM] [succ] <3> vtest
|
|
510
|
[17:06:29.629][HI_APPM] [succ] start voice
|
|
511
|
[17:06:29.629][HI_APPM] [succ] new process(1474)
|
|
512
|
[17:06:29.630][HI_APPM] [succ] <0> sml
|
|
513
|
[17:06:29.644][HI_APPM] [succ] start sml
|
|
514
|
[17:06:29.645][HI_APPM] [succ] new process(1476)
|
|
515
|
[17:06:29.645][HI_APPM] [succ] <0> omci_tapi
|
|
516
|
[17:06:29.765][HI_APPM] [succ] <1> omci_sql
|
|
517
|
[17:06:29.765][HI_APPM] [succ] <2> omci_ctl
|
|
518
|
[17:06:29.773][HI_APPM] [succ] <3> oam
|
|
519
|
[17:06:29.773][HI_APPM] [succ] <4> auto_sensing_ad
|
|
520
|
[17:06:29.774][HI_APPM] [succ] <5> auto_sensing
|
|
521
|
[17:06:29.780][HI_APPM] [succ] start cms
|
|
522
|
[17:06:29.781][HI_APPM] [succ] new process(1479)
|
|
523
|
[17:06:29.825]#Init cm moudle#
|
|
524
|
[17:06:29.869]# Load CM config file#
|
|
525
|
[17:06:29.967]Config_parser Succ.
|
|
526
|
[17:06:29.967]Load Config from config file Succ.
|
|
527
|
[17:06:29.968]Config load Succ!
|
|
528
|
[17:06:29.968]############ Start Distribute CM Config data ############
|
|
529
|
[17:06:29.968][sysuptime: 23] Distribute Early!
|
|
530
|
[17:06:29.968]sendIPCServiceMsg: msgget failed errno=2 No such file or directory, type 1200
|
|
531
|
[17:06:29.977]sendIPCServiceMsg: msgget failed errno=2 No such file or directory, type 1200
|
|
532
|
[17:06:30.416][HI_APPM] [succ] <0> odl
|
|
533
|
[17:06:30.417][HI_APPM] [succ] start cm
|
|
534
|
[17:06:30.428][HI_APPM] [succ] new process(1534)
|
|
535
|
[17:06:30.562][HI_APPM] [succ] <0> cwmp
|
|
536
|
[17:06:30.562][HI_APPM] [succ] start cwmp
|
|
537
|
[17:06:30.563][HI_APPM] [succ] init env
|
|
538
|
[17:06:30.563][HI_APPM] [succ] init cmd
|
|
539
|
[17:06:30.580][HI_APPM] [succ] init monitor
|
|
540
|
[17:06:30.581][HI_APPM] ########### Appm Start End ###########
|
|
541
|
[17:06:30.744][sysuptime: 24] Start init cm remote management module!
|
|
542
|
[17:06:30.759]sendIPCServiceMsg: msgget failed errno=2 No such file or directory, type 1200
|
|
543
|
[17:06:30.759]LOS ALARM CLEAR
|
|
544
|
[17:06:30.759]
|
|
545
|
[17:06:30.759][STDOAM]LLID(0) O1>>>O2
|
|
546
|
[17:06:30.759]
|
|
547
|
[17:06:30.759]Init CTC OAM SUCC!
|
|
548
|
[17:06:30.811]LOS ALARM
|
|
549
|
[17:06:30.811]LOS ALARM CLEAR
|
|
550
|
[17:06:30.811]
|
|
551
|
[17:06:30.811] MPCP llid(0) reg state : 5
|
|
552
|
[17:06:30.811]
|
|
553
|
[17:06:30.811] MPCP llid(0) reg state : 6
|
|
554
|
[17:06:30.821]start epon regist, loid=XEPON4309, lopwd=1234
|
|
555
|
[17:06:30.821]save_uplink_reg_loid XEPON4309 lopwd 1234
|
|
556
|
[17:06:31.363][ctc_regstatus_proc:2550] LOID Register 20
|
|
557
|
[17:06:31.364][May 12 2025-11:22:18], Receive Wan Connection Down Event, WanName [1_TR069_R_VID_46].
|
|
558
|
[17:06:31.364]sendIPCServiceMsg: msgget failed errno=2 No such file or directory, type 1200
|
|
559
|
[17:06:31.378]sendIPCServiceMsg: msgget failed errno=2 No such file or directory, type 1223
|
|
560
|
[17:06:31.407]udhcpc: started, v1.27.2
|
|
561
|
[17:06:31.469][May 12 2025-11:22:18], Receive Wan Connection Down Event, WanName [1_TR069_R_VID_46].
|
|
562
|
[17:06:31.469]sendIPCServiceMsg: msgget failed errno=2 No such file or directory, type 1200
|
|
563
|
[17:06:31.469]sendIPCServiceMsg: msgget failed errno=2 No such file or directory, type 1223
|
|
564
|
[17:06:31.482]udhcpc: [1970-01-01 08:00:25.190] sending discover
|
|
565
|
[17:06:31.763]killall: phddns: no process killed
|
|
566
|
[17:06:31.763][May 12 2025-11:22:18], Receive Wan Connection Add Event, WanName [1_TR069_R_VID_46].
|
|
567
|
[17:06:31.763]
|
|
568
|
[17:06:31.779] error=0x7000000e function=__qos_wan_mixapp_add line=889
|
|
569
|
[17:06:31.992][sysuptime: 25] Distribute Main!
|
|
570
|
[17:06:32.067]sendIPCServiceMsg: msgget failed errno=2 No such file or directory, type 1200
|
|
571
|
[17:06:34.705][sysuptime: 28] Distribute Medium!
|
|
572
|
[17:06:34.705]run easymesh daemon
|
|
573
|
[17:06:35.885][MPCP]LLID(0): O1 => O2
|
|
574
|
[17:06:35.885]
|
|
575
|
[17:06:35.885] MPCP llid(0) reg state : 1
|
|
576
|
[17:06:35.885]iLOS ALARM CLEAR
|
|
577
|
[17:06:35.885]nit oam llid(0)
|
|
578
|
[17:06:35.885]
|
|
579
|
[17:06:35.885][STDOAM]LLID(0) O1>>>O2
|
|
580
|
[17:06:35.885]
|
|
581
|
[17:06:35.897]Init CTC OAM SUCC!
|
|
582
|
[17:06:36.721]nf_conntrack_rtsp v0.7 loading
|
|
583
|
[17:06:36.721]nf_nat_rtsp v0.7 loading
|
|
584
|
[17:06:37.051]sendIPCServiceMsg: msgget failed errno=2 No such file or directory, type 1233
|
|
585
|
[17:06:37.399][MPCP]LLID(0): O2 => O3
|
|
586
|
[17:06:37.399]
|
|
587
|
[17:06:37.399] MPCP llid(0) reg state : 2
|
|
588
|
[17:06:37.473]
|
|
589
|
[17:06:37.474][STDOAM]LLID(0) O2>>>O3
|
|
590
|
[17:06:37.474]
|
|
591
|
[17:06:37.474][STDOAM]LLID(0) O3>>>O4
|
|
592
|
[17:06:37.474]
|
|
593
|
[17:06:37.486][CTCOAM]LLID(0) O1>>>O2
|
|
594
|
[17:06:37.486]
|
|
595
|
[17:06:37.486][CTCOAM]LLID(0) O2>>>O3
|
|
596
|
[17:06:37.486]
|
|
597
|
[17:06:37.486][CTCOAM]LLID(0) O3>>>O4
|
|
598
|
[17:06:37.486]
|
|
599
|
[17:06:37.486][EPON]LLID(0) Online!
|
|
600
|
[17:06:37.486]
|
|
601
|
[17:06:37.505] ctcoam llid(0) reg state : 1
|
|
602
|
[17:06:37.505]
|
|
603
|
[17:06:37.505] ctcoam llid(0) reg state : 2
|
|
604
|
[17:06:37.505]
|
|
605
|
[17:06:37.506] ctcoam llid(0) reg state : 3
|
|
606
|
[17:06:38.173]chpasswd: password for 'telnetadmin_telnet' changed
|
|
607
|
[17:06:38.174]TELNET_ENABLE: 1 TELNET_PORT: 23 TELNET_WAN_PORT: 23
|
|
608
|
[17:06:38.182]killall: telnetd: no process killed
|
|
609
|
[17:06:38.259]FTP_ENABLE: 0 FTP_PORT: 21 FTP_ANONYMOUS: NO FTP_USER: 12345_ftp FTP_IP: 192.168.1.1 FTP_WAN:null
|
|
610
|
[17:06:38.259]killall: vsftpd: no process killed
|
|
611
|
[17:06:38.259]sed: /tmp/etc/vsftpd/user_list: No such file or directory
|
|
612
|
[17:06:38.259]chown: /tmp/etc/vsftpd.conf: No such file or directory
|
|
613
|
[17:06:38.259]chown: /tmp/etc/vsftpd_wan.conf: No such file or directory
|
|
614
|
[17:06:38.260]chown: /tmp/etc/vsftpd/user_list: No such file or directory
|
|
615
|
[17:06:38.260]SSH_ENABLE: 0 SSH_USER: SSH_PASSWD: SSH_PORT:
|
|
616
|
[17:06:38.275]killall: dropbear: no process killed
|
|
617
|
[17:06:38.501]__!!!!!!!_Service_Num=1 g_Service_Name=VOIP
|
|
618
|
[17:06:38.817]__!!!!!!!_Service_Num=1 g_Service_Name=VOIP
|
|
619
|
[17:06:38.970]
|
|
620
|
[17:06:39.001]Login: urandom_read: 1 callbacks suppressed
|
|
621
|
[17:06:39.001]random: dnsmasq: uninitialized urandom read (128 bytes read)
|
|
622
|
[17:06:39.017]random: dnsmasq: uninitialized urandom read (48 bytes read)
|
|
623
|
[17:06:39.297]sendIPCServiceMsg: msgget failed errno=2 No such file or directory, type 1200
|
|
624
|
[17:06:39.297][sysuptime: 33] Distribute Tardy!
|
|
625
|
[17:06:39.298]ulIPver: 0 ulPingCnt: 4 ulBlkSize: 56 ulTimeout: 10000 ulInterval: 0 acWanIf: acHost:
|
|
626
|
[17:06:39.298]pc_waninterface:
|
|
627
|
[17:06:39.298]ifname: host:
|
|
628
|
[17:06:39.302]___pIgdPMUsbGlobalCfgAttrTab->ucUsbShare=0
|
|
629
|
[17:06:39.459]CM RepNum: 5
|
|
630
|
[17:06:39.460]INFO [HI_EmAgentApiInit:432]HI_EmAgentApiInit success
|
|
631
|
[17:06:39.470][XML_WRN:_mib_chain_get(243)] recordNum(0), id(607), final_idx(0), pCurr(0), pCurr->pData(0)
|
|
632
|
[17:06:39.846][XML_WRN:_mib_chain_get(243)] recordNum(0), id(747), final_idx(1), pCurr(0), pCurr->pData(0)
|
|
633
|
[17:06:39.862][sysuptime: 33] Distribute Finish!
|
|
634
|
[17:06:40.012]Start webserver now
|
|
635
|
[17:06:40.012]#####Oprator:1, Area:0 PonRegType: 0####
|
|
636
|
[17:06:40.041]*************ipc_service main**************
|
|
637
|
[17:06:40.041]
|
|
638
|
[17:06:40.041]ipc_service init start!
|
|
639
|
[17:06:40.092][HI_IPC] ipc call hi_IPC_igdCmConfGetallIndex_call fail, pid 1479 ret 72200008, data0[0]
|
|
640
|
[17:06:40.099][HI_IPC] ipc call hi_IPC_igdCmConfGetallIndex_call fail, pid 1479 ret 72200008, data0[0]
|
|
641
|
[17:06:40.159][HI_IPC] ipc call hi_IPC_igdCmConfGetallIndex_call fail, pid 1479 ret 72200008, data0[0]
|
|
642
|
[17:06:40.251]g_ssidnum_band[0]=0
|
|
643
|
[17:06:40.251]g_ssidnum_band[1]=0
|
|
644
|
[17:06:40.266][HI_IPC] ipc call hi_IPC_igdCmConfGetallIndex_call fail, pid 1479 ret 72200008, data0[0]
|
|
645
|
[17:06:40.267]ipc_service conn init succ!
|
|
646
|
[17:06:40.280]ipc_service update proc init!
|
|
647
|
[17:06:40.280]ipc_service init finished!
|
|
648
|
[17:06:40.413][smart] ipc_service finish, start smart firmware !!!
|
|
649
|
[17:06:40.512][smart] start smart firmware finish
|
|
650
|
[17:06:40.512]en : 0x1
|
|
651
|
[17:06:40.512]chk_time : 0x1
|
|
652
|
[17:06:40.512]wait_time : 0x5
|
|
653
|
[17:06:40.512]los_cnt : 0x5
|
|
654
|
[17:06:40.520]reg_check_time : 0xf
|
|
655
|
[17:06:40.520]succ.
|
|
656
|
[17:06:40.581]saf_add_masquerade_rule 4148
|
|
657
|
[17:06:40.930]mount: can't read '/etc/fstab': No such file or directory
|
|
658
|
[17:06:41.061]cgroup: saf (2311) created nested cgroup for controller "memory" which has incomplete hierarchy support. Nested cgroups may change behavior in the future.
|
|
659
|
[17:06:41.081]cgroup: "memory" requires setting use_hierarchy to 1 on the root
|
|
660
|
[17:06:41.438]udhcpc: [1970-01-01 08:00:35.140] sending discover
|
|
661
|
[17:06:41.575]udhcpc: sending select for 192.168.170.129
|
|
662
|
[17:06:41.648]udhcpc: [1970-01-01 08:00:35.340] lease of 192.168.170.129 obtained, lease time 300
|
|
663
|
[17:06:41.780]RTNETLINK answers: No such file or directory
|
|
664
|
[17:06:41.913][May 12 2025-11:22:18], Receive Wan Connection Up Event, WanName [1_TR069_R_VID_46].
|
|
665
|
[17:06:41.930][May 12 2025-11:22:18], Send Wan Connection Up Message to tr069.
|
|
666
|
[17:06:42.038][May 12 2025-11:22:18][sysuptime: 35], Receive PON Up Event.
|
|
667
|
[17:06:46.318]random: ubusd: uninitialized urandom read (4 bytes read)
|
|
668
|
[17:06:46.319]random: ubusd: uninitialized urandom read (4 bytes read)
|
|
669
|
[17:06:46.332]random: ubusd: uninitialized urandom read (4 bytes read)
|
|
670
|
[17:06:47.707][ctc_regstatus_proc:2558] LOID Register 30
|
|
671
|
[17:06:47.707][ctc_regstatus_proc:2582] LOID Register 40
|
|
672
|
[17:06:47.707][ctc_regstatus_proc:2595] LOID Register 50
|
|
673
|
[17:06:47.713][ctc_regstatus_proc:2620] LOID Register 60
|
|
674
|
[17:06:47.714][ctc_regstatus_proc:2633] LOID Register 70
|
|
675
|
[17:06:47.714][ctc_regstatus_proc:2654] LOID Register 100
|
|
676
|
[17:06:52.847]iptables: No chain/target/match by that name.
|
|
677
|
[17:06:52.860]iptables v1.8.2 (legacy): Couldn't load target `ct_redict_dnat':No such file or directory
|
|
678
|
[17:06:52.860]
|
|
679
|
[17:06:52.861]Try `iptables -h' or 'iptables --help' for more information.
|
|
680
|
[17:06:52.867]iptables: No chain/target/match by that name.
|
|
681
|
[17:06:52.895]iptables: No chain/target/match by that name.
|
|
682
|
[17:06:52.908]iptables v1.8.2 (legacy): Couldn't load target `ct_redict_reject':No such file or directory
|
|
683
|
[17:06:52.908]
|
|
684
|
[17:06:52.908]Try `iptables -h' or 'iptables --help' for more information.
|
|
685
|
[17:06:52.909]iptables: No chain/target/match by that name.
|
|
686
|
[17:06:53.371]sipapp started, File: /home/ply/hsan/gateway/service/voice/adpt/src/voip_api.c, Line: 5887, Function: VOIP_start_app_thread !
|
|
687
|
[17:06:53.779]memshr init OK
|
|
688
|
[17:06:53.785]ctSgw_appRegisterFunc: 250 (ptrval)/(ptrval)/00000000
|
|
689
|
[17:06:53.785]ctSgw_appRegisterForwardProc: 775, prio -190
|
|
690
|
[17:06:53.785]xmit pkt api does not support
|
|
691
|
[17:06:53.796]this is the kernel b01 loaded by m01-b01
|
|
692
|
[17:06:55.750]Init DSP starting...
|
|
693
|
[17:06:55.750]ASIC Init begin
|
|
694
|
[17:06:55.751]LoadZspCode Success, waiting for bootting...
|
|
695
|
[17:06:55.751]zsp_boot Success!
|
|
696
|
[17:06:55.751]ASIC Init end
|
|
697
|
[17:06:55.759]Init DSP OK!
|
|
698
|
[17:06:56.065]random: crng init done
|
|
699
|
[17:06:56.065]random: 1 urandom warning(s) missed due to ratelimiting
|
|
700
|
[17:07:00.078]###########critical_process_check,485############
|
|
701
|
[17:07:00.079]###########critical_process_check,485############
|
|
702
|
[17:07:00.109]###########critical_process_check,485############
|
|
703
|
[17:07:05.130]###########critical_process_check,485############
|
|
704
|
[17:07:07.514]start epon regist, loid=XEPON4320, lopwd=1234
|
|
705
|
[17:07:08.539][ctc_regstatus_proc:2550] LOID Register 20
|
|
706
|
[17:07:10.164]###########critical_process_check,485############
|
|
707
|
[17:07:13.738][MPCP]LLID(0): O1 => O2
|
|
708
|
[17:07:13.738]
|
|
709
|
[17:07:13.738] MPCP llid(0) reg state : 1
|
|
710
|
[17:07:13.738]iLOS ALARM CLEAR
|
|
711
|
[17:07:13.738]nit oam llid(0)
|
|
712
|
[17:07:13.738]
|
|
713
|
[17:07:13.738][STDOAM]LLID(0) O1>>>O2
|
|
714
|
[17:07:13.738]
|
|
715
|
[17:07:13.738]Init CTC OAM SUCC!
|
|
716
|
[17:07:13.738][MPCP]LLID(0): O2 => O3
|
|
717
|
[17:07:13.738]
|
|
718
|
[17:07:13.738] MPCP llid(0) reg state : 2
|
|
719
|
[17:07:13.738]
|
|
720
|
[17:07:13.738][STDOAM]LLID(0) O2>>>O3
|
|
721
|
[17:07:13.738]
|
|
722
|
[17:07:13.739][STDOAM]LLID(0) O3>>>O4
|
|
723
|
[17:07:13.739]
|
|
724
|
[17:07:13.739][CTCOAM]LLID(0) O1>>>O2
|
|
725
|
[17:07:13.739]
|
|
726
|
[17:07:13.739] ctcoam llid(0) reg state : 1
|
|
727
|
[17:07:13.739][CTCOAM]LLID(0) O2>>>O3
|
|
728
|
[17:07:13.739]
|
|
729
|
[17:07:13.739]
|
|
730
|
[17:07:13.739] ctcoam llid(0) reg state :
|
|
731
|
[17:07:13.739][CTCOAM]LLID(0) O3>>>O4
|
|
732
|
[17:07:13.739] 2
|
|
733
|
[17:07:13.739]
|
|
734
|
[17:07:13.739][EPON]LLID(0) Online!
|
|
735
|
[17:07:13.739]
|
|
736
|
[17:07:13.739] ctcoam llid(0) reg state : 3
|
|
737
|
[17:07:17.439]###########critical_process_check,485############
|
|
738
|
[17:07:17.439]cwmpClient server ip[192.168.170.129].
|
|
739
|
[17:07:20.222]###########critical_process_check,485############
|
|
740
|
[17:07:24.620][ctc_regstatus_proc:2558] LOID Register 30
|
|
741
|
[17:07:24.620][ctc_regstatus_proc:2582] LOID Register 40
|
|
742
|
[17:07:24.620][ctc_regstatus_proc:2595] LOID Register 50
|
|
743
|
[17:07:24.620][ctc_regstatus_proc:2620] LOID Register 60
|
|
744
|
[17:07:24.621][ctc_regstatus_proc:2654] LOID Register 100
|
|
745
|
[17:07:25.242]###########critical_process_check,485############
|
|
746
|
[17:07:30.256]###########critical_process_check,485############
|
|
747
|
[17:07:35.301]###########critical_process_check,485############
|
|
748
|
[17:07:40.314]###########critical_process_check,485############
|
|
749
|
[17:07:42.006]dying gasp
|
|
750
|
[17:07:43.739]
|
|
751
|
[17:07:43.739]
|
|
752
|
[17:07:43.739]U-Boot 2022.07 (Feb 27 2025 - 11:23:13 +0800) for emei
|
|
753
|
[17:07:43.739]
|
|
754
|
[17:07:43.739]DRAM: 256 MiB
|
|
755
|
[17:07:43.864]Core: 68 devices, 17 uclasses, devicetree: separate
|
|
756
|
[17:07:43.908]WDT: Started watchdog with servicing (30s timeout)
|
|
757
|
[17:07:43.936]NAND: 256 MiB
|
|
758
|
[17:07:44.243]Loading Environment from NAND... OK
|
|
759
|
[17:07:44.244]In: uart@0x1010f000
|
|
760
|
[17:07:44.244]Out: uart@0x1010f000
|
|
761
|
[17:07:44.244]Err: uart@0x1010f000
|
|
762
|
[17:07:44.301]Hard Power-on reset for internal POR circuit timing
|
|
763
|
[17:07:44.636]Net: Could not get PHY for eth6: addr 1
|
|
764
|
[17:07:44.637]hsan_mac gemac@0: gemac@0 no phy device
|
|
765
|
[17:07:45.108]Could not get PHY for eth7: addr 1
|
|
766
|
[17:07:45.108]hsan_mac gemac@8: gemac@8 no phy device
|
|
767
|
[17:07:45.109]eth0: pie
|
|
768
|
[17:07:45.137]bootflag b bootreg 0
|
|
769
|
[17:07:45.137]bootreg init, set 11
|
|
770
|
[17:07:53.366]Hit any key to stop autoboot: 0
|
|
771
|
[17:07:54.129]Reading 6291456 byte(s) (3072 page(s)) at offset 0x00000000
|
|
772
|
[17:07:54.747]bootreg offset: c08
|
|
773
|
[17:07:54.747]boot regval: 11
|
|
774
|
[17:07:54.747] Image Name: Linux-5.10.0
|
|
775
|
[17:07:54.747] Image Type: ARM Linux Kernel Image (uncompressed)
|
|
776
|
[17:07:54.766] Data Size: 6091416 Bytes = 5.8 MiB
|
|
777
|
[17:07:54.766] Load Address: 80208000
|
|
778
|
[17:07:54.766] Entry Point: 80208000
|
|
779
|
[17:07:55.142]alias console=/uart@0x1010f000
|
|
780
|
[17:07:55.143]serialnr->high=0x8250, serialnr->low=0x1010f000, atag_addr=0x80200100
|
|
781
|
[17:07:58.210]Uncompressing Linux... done, booting the kernel.
|
|
782
|
[17:07:58.298]Booting Linux on physical CPU 0x0
|
|
783
|
[17:07:58.299]Linux version 5.10.0 (ply@ubuntu22.04) (arm-mix510-linux-gcc (musl-1.2.3 linux-5.10 V12CS61.003.020 2024-01-16 12:00:00) 10.3.0, GNU ld (GNU Binutils) 2.38) #2 SMP Mon May 12 11:22:40 CST 2025
|
|
784
|
[17:07:58.299]CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=18c5387d
|
|
785
|
[17:07:58.299]CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
|
|
786
|
[17:07:58.299]OF: fdt: Machine model: hsan-emei
|
|
787
|
[17:07:58.299]OF: fdt: Ignoring memory range 0x80000000 - 0x80200000
|
|
788
|
[17:07:58.300]earlycon: uart0 at MMIO 0x1010f000 (options '')
|
|
789
|
[17:07:58.300]printk: bootconsole [uart0] enabled
|
|
790
|
[17:07:58.300]Memory policy: Data cache writealloc
|
|
791
|
[17:07:58.300]Zone ranges:
|
|
792
|
[17:07:58.300] Normal [mem 0x0000000080200000-0x000000009fffffff]
|
|
793
|
[17:07:58.300]Movable zone start for each node
|
|
794
|
[17:07:58.300]Early memory node ranges
|
|
795
|
[17:07:58.300] node 0: [mem 0x0000000080200000-0x00000000874fffff]
|
|
796
|
[17:07:58.301] node 0: [mem 0x0000000088000000-0x00000000888fffff]
|
|
797
|
[17:07:58.305] node 0: [mem 0x0000000088a00000-0x000000009fffffff]
|
|
798
|
[17:07:58.308]Zeroed struct page in unavailable ranges: 1024 pages
|
|
799
|
[17:07:58.308]Initmem setup node 0 [mem 0x0000000080200000-0x000000009fffffff]
|
|
800
|
[17:07:58.354]mdesc->l2c_aux_val 430001 mdesc->l2c_aux_mask ffb0fffe
|
|
801
|
[17:07:58.355]percpu: Embedded 20 pages/cpu s50636 r8192 d23092 u81920
|
|
802
|
[17:07:58.355]Built 1 zonelists, mobility grouping on. Total pages: 126340
|
|
803
|
[17:07:58.355]Kernel command line: noinitrd cma=0 console=ttyS0,115200 earlycon maxcpus=2 nr_cpus=2 additional_cpus=1
|
|
804
|
[17:07:58.355]Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
|
|
805
|
[17:07:58.367]Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
|
|
806
|
[17:07:58.367]mem auto-init: stack:off, heap alloc:off, heap free:off
|
|
807
|
[17:07:58.670]Memory: 488280K/509952K available (9494K kernel code, 1445K rwdata, 2972K rodata, 1720K init, 551K bss, 21672K reserved, 0K cma-reserved)
|
|
808
|
[17:07:58.673]SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
|
|
809
|
[17:07:58.673]rcu: Hierarchical RCU implementation.
|
|
810
|
[17:07:58.673] Tracing variant of Tasks RCU enabled.
|
|
811
|
[17:07:58.673]rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
|
|
812
|
[17:07:58.674]NR_IRQS: 16, nr_irqs: 192, preallocated irqs: 192
|
|
813
|
[17:07:58.674]L2C: platform modifies aux control register: 0x02030000 -> 0x02430001
|
|
814
|
[17:07:58.674]L2C: DT/platform modifies aux control register: 0x02030000 -> 0x02430001
|
|
815
|
[17:07:58.674]L2C: DT/platform tries to modify or specify cache size
|
|
816
|
[17:07:58.674]L2C-310 erratum 769419 enabled
|
|
817
|
[17:07:58.674]L2C-310 enabling early BRESP for Cortex-A9
|
|
818
|
[17:07:58.674]L2C-310: enabling full line of zeros but not enabled in Cortex-A9
|
|
819
|
[17:07:58.675]L2C-310 dynamic clock gating enabled, standby mode enabled
|
|
820
|
[17:07:58.675]L2C-310 cache controller enabled, 16 ways, 256 kB
|
|
821
|
[17:07:58.675]L2C-310: CACHE_ID 0x410000c9, AUX_CTRL 0x46430001
|
|
822
|
[17:07:58.675]random: get_random_bytes called from start_kernel+0x380/0x578 with crng_init=0
|
|
823
|
[17:07:58.675]clocksource: arm,sp804: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604467 ns
|
|
824
|
[17:07:58.675]sched_clock: 32 bits at 100MHz, resolution 10ns, wraps every 21474836475ns
|
|
825
|
[17:07:58.676]sched_clock: 64 bits at 200MHz, resolution 5ns, wraps every 4398046511102ns
|
|
826
|
[17:07:58.676]clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x2e2049d3e8, max_idle_ns: 440795210634 ns
|
|
827
|
[17:07:58.676]Switching to timer-based delay loop, resolution 5ns
|
|
828
|
[17:07:58.676]Calibrating delay loop (skipped), value calculated using timer frequency.. 400.00 BogoMIPS (lpj=2000000)
|
|
829
|
[17:07:58.676]pid_max: default: 32768 minimum: 301
|
|
830
|
[17:07:58.677]Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
|
|
831
|
[17:07:58.677]Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
|
|
832
|
[17:07:58.677]CPU: Testing write buffer coherency: ok
|
|
833
|
[17:07:58.677]CPU0: Spectre v2: using BPIALL workaround
|
|
834
|
[17:07:58.677]CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
|
|
835
|
[17:07:58.678]Setting up static identity map for 0x80208220 - 0x80208280
|
|
836
|
[17:07:58.687]rcu: Hierarchical SRCU implementation.
|
|
837
|
[17:07:58.687]smp: Bringing up secondary CPUs ...
|
|
838
|
[17:07:58.687]CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
|
|
839
|
[17:07:58.687]CPU1: Spectre v2: using BPIALL workaround
|
|
840
|
[17:07:58.687]smp: Brought up 1 node, 2 CPUs
|
|
841
|
[17:07:58.687]SMP: Total of 2 processors activated (800.00 BogoMIPS).
|
|
842
|
[17:07:58.688]CPU: All CPU(s) started in SVC mode.
|
|
843
|
[17:07:58.688]allocated 524288 bytes of page_ext
|
|
844
|
[17:07:58.688]devtmpfs: initialized
|
|
845
|
[17:07:58.688]clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
|
|
846
|
[17:07:58.688]futex hash table entries: 512 (order: 3, 32768 bytes, linear)
|
|
847
|
[17:07:58.688]pinctrl core: initialized pinctrl subsystem
|
|
848
|
[17:07:58.689]NET: Registered protocol family 16
|
|
849
|
[17:07:58.689]DMA: preallocated 256 KiB pool for atomic coherent allocations
|
|
850
|
[17:07:58.689]thermal_sys: Registered thermal governor 'fair_share'
|
|
851
|
[17:07:58.689]thermal_sys: Registered thermal governor 'bang_bang'
|
|
852
|
[17:07:58.689]thermal_sys: Registered thermal governor 'step_wise'
|
|
853
|
[17:07:58.689]thermal_sys: Registered thermal governor 'user_space'
|
|
854
|
[17:07:58.689]thermal_sys: Registered thermal governor 'power_allocator'
|
|
855
|
[17:07:58.690]hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
|
|
856
|
[17:07:58.690]hw-breakpoint: maximum watchpoint size is 4 bytes.
|
|
857
|
[17:07:58.690]Serial: AMBA PL011 UART driver
|
|
858
|
[17:07:58.718]OF: /gpio@0x10106000/gpio-port@0: could not get #gpio-cells for /mii_misc@0
|
|
859
|
[17:07:58.718]OF: /gpio@0x10107000/gpio-port@0: could not get #gpio-cells for /mdio0/ethernet-phy@1
|
|
860
|
[17:07:58.728]SCSI subsystem initialized
|
|
861
|
[17:07:58.729]usbcore: registered new interface driver usbfs
|
|
862
|
[17:07:58.729]usbcore: registered new interface driver hub
|
|
863
|
[17:07:58.729]usbcore: registered new device driver usb
|
|
864
|
[17:07:58.729]NET: Registered protocol family 8
|
|
865
|
[17:07:58.730]NET: Registered protocol family 20
|
|
866
|
[17:07:58.745]clocksource: Switched to clocksource arm_global_timer
|
|
867
|
[17:07:58.977]VFS: Disk quotas dquot_6.6.0
|
|
868
|
[17:07:58.977]VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
|
|
869
|
[17:07:58.977]FS-Cache: Loaded
|
|
870
|
[17:07:58.977]CacheFiles: Loaded
|
|
871
|
[17:07:58.978]NET: Registered protocol family 2
|
|
872
|
[17:07:58.978]tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
|
|
873
|
[17:07:58.978]TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
|
|
874
|
[17:07:58.978]TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear)
|
|
875
|
[17:07:58.978]TCP: Hash tables configured (established 4096 bind 4096)
|
|
876
|
[17:07:58.978]UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
|
|
877
|
[17:07:58.979]UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
|
|
878
|
[17:07:58.979]NET: Registered protocol family 1
|
|
879
|
[17:07:58.979]RPC: Registered named UNIX socket transport module.
|
|
880
|
[17:07:58.979]RPC: Registered udp transport module.
|
|
881
|
[17:07:58.979]RPC: Registered tcp transport module.
|
|
882
|
[17:07:58.987]RPC: Registered tcp NFSv4.1 backchannel transport module.
|
|
883
|
[17:07:58.987]NET: Registered protocol family 44
|
|
884
|
[17:07:58.987]PCI: CLS 0 bytes, default 64
|
|
885
|
[17:07:59.103]Initialise system trusted keyrings
|
|
886
|
[17:07:59.103]workingset: timestamp_bits=14 max_order=17 bucket_order=3
|
|
887
|
[17:07:59.103]squashfs: version 4.0 (2009/01/31) Phillip Lougher
|
|
888
|
[17:07:59.104]ntfs: driver 2.1.32 [Flags: R/W DEBUG].
|
|
889
|
[17:07:59.104]jffs2: version 2.2. (NAND) (SUMMARY) ? 2001-2006 Red Hat, Inc.
|
|
890
|
[17:07:59.121]fuse: init (API version 7.32)
|
|
891
|
[17:07:59.449]Key type asymmetric registered
|
|
892
|
[17:07:59.449]Asymmetric key parser 'x509' registered
|
|
893
|
[17:07:59.449]Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
|
|
894
|
[17:07:59.449]Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
|
|
895
|
[17:07:59.449]printk: console [ttyS0] disabled
|
|
896
|
[17:07:59.450]1010f000.uart: ttyS0 at MMIO 0x1010f000 (irq = 205, base_baud = 6250000) is a 16550A
|
|
897
|
[17:07:59.450]printk: console [ttyS0] enabled
|
|
898
|
[17:07:59.450]printk: console [ttyS0] enabled
|
|
899
|
[17:07:59.451]printk: bootconsole [uart0] disabled
|
|
900
|
[17:07:59.451]printk: bootconsole [uart0] disabled
|
|
901
|
[17:07:59.452]libphy: Fixed MDIO Bus: probed
|
|
902
|
[17:07:59.452]PPP generic driver version 2.4.2
|
|
903
|
[17:07:59.452]PPP MPPE Compression module registered
|
|
904
|
[17:07:59.452]NET: Registered protocol family 24
|
|
905
|
[17:07:59.453]SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
|
|
906
|
[17:07:59.453]CSLIP: code copyright 1989 Regents of the University of California.
|
|
907
|
[17:07:59.453]SLIP linefill/keepalive option.
|
|
908
|
[17:07:59.453]usbcore: registered new interface driver uas
|
|
909
|
[17:07:59.453]usbcore: registered new interface driver usb-storage
|
|
910
|
[17:07:59.453]usbcore: registered new interface driver usbserial_generic
|
|
911
|
[17:07:59.453]usbserial: USB Serial support registered for generic
|
|
912
|
[17:07:59.454]usbcore: registered new interface driver ch341
|
|
913
|
[17:07:59.454]usbserial: USB Serial support registered for ch341-uart
|
|
914
|
[17:07:59.454]usbcore: registered new interface driver cp210x
|
|
915
|
[17:07:59.454]usbserial: USB Serial support registered for cp210x
|
|
916
|
[17:07:59.454]usbcore: registered new interface driver ftdi_sio
|
|
917
|
[17:07:59.454]usbserial: USB Serial support registered for FTDI USB Serial Device
|
|
918
|
[17:07:59.454]usbcore: registered new interface driver pl2303
|
|
919
|
[17:07:59.455]usbserial: USB Serial support registered for pl2303
|
|
920
|
[17:07:59.457]GACT probability NOT on
|
|
921
|
[17:07:59.457]Mirror/redirect action on
|
|
922
|
[17:07:59.457]u32 classifier
|
|
923
|
[17:07:59.457] input device check on
|
|
924
|
[17:07:59.457] Actions configured
|
|
925
|
[17:07:59.458]xt_time: kernel timezone is -0000
|
|
926
|
[17:07:59.458]ipip: IPv4 and MPLS over IPv4 tunneling driver
|
|
927
|
[17:07:59.458]Initializing XFRM netlink socket
|
|
928
|
[17:07:59.458]NET: Registered protocol family 10
|
|
929
|
[17:07:59.458]Segment Routing with IPv6
|
|
930
|
[17:07:59.458]sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
|
|
931
|
[17:07:59.458]NET: Registered protocol family 17
|
|
932
|
[17:07:59.458]Bridge firewalling registered
|
|
933
|
[17:07:59.459]l2tp_core: L2TP core driver, V2.0
|
|
934
|
[17:07:59.459]l2tp_ppp: PPPoL2TP kernel driver, V2.0
|
|
935
|
[17:07:59.459]l2tp_ip: L2TP IP encapsulation support (L2TPv3)
|
|
936
|
[17:07:59.459]l2tp_netlink: L2TP netlink interface
|
|
937
|
[17:07:59.459]l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
|
|
938
|
[17:07:59.459]l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
|
|
939
|
[17:07:59.459]8021q: 802.1Q VLAN Support v1.8
|
|
940
|
[17:07:59.459]lib80211: common routines for IEEE802.11 drivers
|
|
941
|
[17:07:59.460]Registering SWP/SWPB emulation handler
|
|
942
|
[17:07:59.460]Loading compiled-in X.509 certificates
|
|
943
|
[17:07:59.460]cfg80211: Loading compiled-in X.509 certificates for regulatory database
|
|
944
|
[17:07:59.460]cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
|
|
945
|
[17:07:59.460]platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
|
|
946
|
[17:07:59.460]cfg80211: failed to load regulatory.db
|
|
947
|
[17:07:59.460]Warning: unable to open an initial console.
|
|
948
|
[17:07:59.461]Freeing unused kernel memory: 1720K
|
|
949
|
[17:07:59.463]Kernel memory protection not selected by kernel config.
|
|
950
|
[17:07:59.463]Run /init as init process
|
|
951
|
[17:07:59.516]hi_crg: loading out-of-tree module taints kernel.
|
|
952
|
[17:07:59.516][DFX]
|
|
953
|
[17:07:59.532] HSAN mlog_print function is unavailable...
|
|
954
|
[17:07:59.532]Basic driver of Linux Kernel install successfully ...!
|
|
955
|
[17:07:59.548]1010e000.uart: ttyS1 at MMIO 0x1010e000 (irq = 206, base_baud = 6250000) is a 16550A
|
|
956
|
[17:07:59.608]hi-reset reset@0: resister reset device
|
|
957
|
[17:07:59.608]hi-reset reset@1: resister reset device
|
|
958
|
[17:07:59.608]hi-reset reset@2: resister reset device
|
|
959
|
[17:07:59.615]10a40000.usb_ehci_acp : ON
|
|
960
|
[17:07:59.615]10600000.usb_xhci_acp : ON
|
|
961
|
[17:07:59.615]10160000.pcie_acp : OFF
|
|
962
|
[17:07:59.616]10164000.pcie_acp : OFF
|
|
963
|
[17:07:59.619]10a70000.pie_acp : ON
|
|
964
|
[17:07:59.620]hsan-watchdog-driver 14880000.watchdog: Hsan watchdog timeout=30 sec, nowayout=1
|
|
965
|
[17:07:59.689]HSAN FMC Controller Device Driver, Version 100
|
|
966
|
[17:07:59.689]15 fixed-partitions partitions found on MTD device 10a20000.fmc
|
|
967
|
[17:07:59.689]Creating 15 MTD partitions on "10a20000.fmc":
|
|
968
|
[17:07:59.689]0x000000000000-0x000000100000 : "uboot"
|
|
969
|
[17:07:59.689]0x000000100000-0x000000140000 : "enva"
|
|
970
|
[17:07:59.698]0x000000140000-0x000000180000 : "envb"
|
|
971
|
[17:07:59.698]0x000000180000-0x000000380000 : "fac"
|
|
972
|
[17:07:59.699]0x000000380000-0x000000580000 : "cfga"
|
|
973
|
[17:07:59.740]0x000000580000-0x000000780000 : "cfgb"
|
|
974
|
[17:07:59.741]0x000000780000-0x000000c40000 : "log"
|
|
975
|
[17:07:59.741]0x000000c40000-0x000000c80000 : "pstore"
|
|
976
|
[17:07:59.771]0x000000c80000-0x000001280000 : "kernela"
|
|
977
|
[17:07:59.771]0x000001280000-0x000001880000 : "kernelb"
|
|
978
|
[17:07:59.771]0x000001880000-0x000006080000 : "rootfsa"
|
|
979
|
[17:07:59.772]0x000006080000-0x00000a880000 : "rootfsb"
|
|
980
|
[17:07:59.772]0x00000a880000-0x00000b880000 : "fwka"
|
|
981
|
[17:07:59.772]0x00000b880000-0x00000c880000 : "fwkb"
|
|
982
|
[17:07:59.786]0x00000c880000-0x000010000000 : "app"
|
|
983
|
[17:07:59.850]show boot_reg: 10
|
|
984
|
[17:07:59.850]ubi0: attaching mtd11
|
|
985
|
[17:08:00.019]ubi0: scanning is finished
|
|
986
|
[17:08:00.019]ubi0 error: ubi_read_volume_table [ubi]: the layout volume was not found
|
|
987
|
[17:08:00.032]ubi0 error: ubi_attach_mtd_dev [ubi]: failed to attach mtd11, error -22
|
|
988
|
[17:08:00.032]UBI error: cannot attach mtd11
|
|
989
|
[17:08:00.033]UBI error: cannot initialize UBI, error -22
|
|
990
|
[17:08:05.182]
|
|
991
|
[17:08:05.182]pie module commit_id:1195a7f5
|
|
992
|
[17:08:05.182]
|
|
993
|
[17:08:05.182]clipper module commit_id:1195a7f5
|
|
994
|
[17:08:05.182]pie 10a70000.pie: open dma-coherent 3000000
|
|
995
|
[17:08:05.190]pie 10a70000.pie: Hisilicon pie swver=v210,hwver=v200
|
|
996
|
[17:08:05.251]
|
|
997
|
[17:08:05.253]mdio module commit_id:1195a7f5
|
|
998
|
[17:08:05.285]libphy: hi_mii_bus: probed
|
|
999
|
[17:08:05.328]
|
|
1000
|
[17:08:05.328]phy module commit_id:1195a7f5
|
|
1001
|
[17:08:05.554][GEPHY]Genius Phy hwVer:0x20669a0e fwVer:0x6807
|
|
1002
|
[17:08:05.554]
|
|
1003
|
[17:08:05.554]phy module commit_id:1195a7f5
|
|
1004
|
[17:08:05.554]
|
|
1005
|
[17:08:05.554]phy module commit_id:1195a7f5
|
|
1006
|
[17:08:05.554]
|
|
1007
|
[17:08:05.569]phy module commit_id:1195a7f5
|
|
1008
|
[17:08:05.593]
|
|
1009
|
[17:08:05.593]mac module commit_id:1195a7f5
|
|
1010
|
[17:08:05.593]
|
|
1011
|
[17:08:05.593]mac module commit_id:1195a7f5
|
|
1012
|
[17:08:05.593]
|
|
1013
|
[17:08:05.593]mac module commit_id:1195a7f5
|
|
1014
|
[17:08:05.593]
|
|
1015
|
[17:08:05.601]mac module commit_id:1195a7f5
|
|
1016
|
[17:08:05.646]
|
|
1017
|
[17:08:05.646]misc module commit_id:1195a7f5
|
|
1018
|
[17:08:05.658]mii_misc 14890138.mii_misc: Hisilicon mii misc driver init
|
|
1019
|
[17:08:05.658]
|
|
1020
|
[17:08:05.659]pcs module commit_id:1195a7f5
|
|
1021
|
[17:08:05.691]pcs 14e00000.pcs: Hisilicon pcs driver init
|
|
1022
|
[17:08:05.691]
|
|
1023
|
[17:08:05.692]team module commit_id:1195a7f5
|
|
1024
|
[17:08:05.692]
|
|
1025
|
[17:08:05.692]
|
|
1026
|
[17:08:05.709]lsw module commit_id:1195a7f5
|
|
1027
|
[17:08:05.709]
|
|
1028
|
[17:08:05.722]
|
|
1029
|
[17:08:05.722]dp module commit_id:1195a7f5
|
|
1030
|
[17:08:05.722]
|
|
1031
|
[17:08:05.723]failed to find hsan,queue_reserved node
|
|
1032
|
[17:08:05.723]failed to find hsan,flow_reserved node
|
|
1033
|
[17:08:05.734][LSW]Hisilicon lsw dp swver=v300,hwver=v200,ret=0x0
|
|
1034
|
[17:08:05.783]
|
|
1035
|
[17:08:05.783]pfe module commit_id:1195a7f5
|
|
1036
|
[17:08:05.783]
|
|
1037
|
[17:08:05.820][LSW]Hisilicon lsw pfe swver=v200,hwver=v200,ret=0x0
|
|
1038
|
[17:08:05.820]
|
|
1039
|
[17:08:05.820]cfe pub module commit_id:4319684c
|
|
1040
|
[17:08:05.827][CFE]CFE PUB module install successfully ...!
|
|
1041
|
[17:08:05.948]
|
|
1042
|
[17:08:05.948]cfe lrn module commit_id:4319684c
|
|
1043
|
[17:08:05.949][CFE]CFE LRN module install successfully ...!
|
|
1044
|
[17:08:05.949]
|
|
1045
|
[17:08:05.949]l3 lib module commit_id:4319684c
|
|
1046
|
[17:08:05.949][CFE]L3 LIB module install successfully ...!
|
|
1047
|
[17:08:05.949]
|
|
1048
|
[17:08:05.949]l4 lib module commit_id:4319684c
|
|
1049
|
[17:08:05.949][CFE]L4 LIB module install successfully ...!
|
|
1050
|
[17:08:05.949]
|
|
1051
|
[17:08:05.949]l2tp lib module commit_id:4319684c
|
|
1052
|
[17:08:05.949][CFE]L2TP LIB module install successfully ...!
|
|
1053
|
[17:08:05.949]
|
|
1054
|
[17:08:05.949]dslite lib module commit_id:4319684c
|
|
1055
|
[17:08:05.950][CFE]DSLITE LIB module install successfully ...!
|
|
1056
|
[17:08:05.950]
|
|
1057
|
[17:08:05.950]mc lib module commit_id:4319684c
|
|
1058
|
[17:08:05.950][CFE]MC LIB module install successfully ...!
|
|
1059
|
[17:08:05.950]
|
|
1060
|
[17:08:05.950]mc list module commit_id:4319684c
|
|
1061
|
[17:08:05.950][CFE]MC LIST module install successfully ...!
|
|
1062
|
[17:08:05.950]
|
|
1063
|
[17:08:05.950]vxlan lib module commit_id:4319684c
|
|
1064
|
[17:08:05.964][CFE]VXLAN LIB module install successfully ...!
|
|
1065
|
[17:08:05.977]
|
|
1066
|
[17:08:05.978]cfe adp capa module commit_id:4319684c
|
|
1067
|
[17:08:06.027]
|
|
1068
|
[17:08:06.027]hslink module commit_id:4319684c
|
|
1069
|
[17:08:06.027][HSLINK]HSLINK install successfully ...!
|
|
1070
|
[17:08:06.027]
|
|
1071
|
[17:08:06.027]serdes module commit_id:1195a7f5
|
|
1072
|
[17:08:06.027]
|
|
1073
|
[17:08:06.115]i2c /dev entries driver
|
|
1074
|
[17:08:06.115]
|
|
1075
|
[17:08:06.116]pon_core module commit_id:1195a7f5
|
|
1076
|
[17:08:06.116]
|
|
1077
|
[17:08:06.116]
|
|
1078
|
[17:08:06.116][PON]pon_core module install succ!
|
|
1079
|
[17:08:06.147]
|
|
1080
|
[17:08:06.147]ploam module commit_id:1195a7f5
|
|
1081
|
[17:08:06.147]
|
|
1082
|
[17:08:06.147][PON]pon_ploam module install succ!
|
|
1083
|
[17:08:06.148]
|
|
1084
|
[17:08:06.148]pon_glb module commit_id:1195a7f5
|
|
1085
|
[17:08:06.148]
|
|
1086
|
[17:08:06.148]pon optical module tx en level [0]
|
|
1087
|
[17:08:06.149]pon optical module rx los level [0]
|
|
1088
|
[17:08:06.160][PON]pon_global module install succ!
|
|
1089
|
[17:08:06.191]
|
|
1090
|
[17:08:06.191]gmac module commit_id:1195a7f5
|
|
1091
|
[17:08:06.191]
|
|
1092
|
[17:08:06.191][PON]pon_gmac module install succ!
|
|
1093
|
[17:08:06.191]
|
|
1094
|
[17:08:06.191]emac module commit_id:1195a7f5
|
|
1095
|
[17:08:06.191]
|
|
1096
|
[17:08:06.207][PON]pon_emac module install succ!
|
|
1097
|
[17:08:06.252]
|
|
1098
|
[17:08:06.252]mpcp module commit_id:1195a7f5
|
|
1099
|
[17:08:06.252]
|
|
1100
|
[17:08:06.252][PON]pon_mpcp module install succ!
|
|
1101
|
[17:08:06.281]dw-apb-uart 1010f000.uart: forbid DMA for kernel console
|
|
1102
|
[17:08:06.281]mount file system start
|
|
1103
|
[17:08:07.493]Changing password for root
|
|
1104
|
[17:08:07.493]New password:
|
|
1105
|
[17:08:07.493]Bad password: too weak
|
|
1106
|
[17:08:07.493]Retype password:
|
|
1107
|
[17:08:07.503]passwd: password for root changed by root
|
|
1108
|
[17:08:07.503]mount file system end
|
|
1109
|
[17:08:07.765]permission adapt start
|
|
1110
|
[17:08:07.881]permission adapt end
|
|
1111
|
[17:08:09.816]module rootkit_infection_detection init success. kln_address=c00be93c
|
|
1112
|
[17:08:09.816]The board info is vendor_id=hsan, chip_id=emei, board_id=0(0x0)
|
|
1113
|
[17:08:09.819]The board.xml is exist, keep old board.xml
|
|
1114
|
[17:08:09.819]init board
|
|
1115
|
[17:08:09.881]sysctl_conf start
|
|
1116
|
[17:08:09.881]sysctl_conf end
|
|
1117
|
[17:08:09.881]ln /etc/localtime
|
|
1118
|
[17:08:09.985][HI_APPM] ########### Appm Start Begin ###########
|
|
1119
|
[17:08:09.985]appm init begin
|
|
1120
|
[17:08:10.033]begin ctc_smart_prepare !!!
|
|
1121
|
[17:08:10.034]ubi0: attaching mtd14
|
|
1122
|
[17:08:10.238]ubi0: scanning is finished
|
|
1123
|
[17:08:10.238]
|
|
1124
|
[17:08:10.238]gateway module commit_id:ffffffff
|
|
1125
|
[17:08:10.238]
|
|
1126
|
[17:08:10.238]
|
|
1127
|
[17:08:10.238] hi_notify_init succ
|
|
1128
|
[17:08:10.238]ubi0: attached mtd14 (name "app", size 55 MiB)
|
|
1129
|
[17:08:10.239]ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
|
|
1130
|
[17:08:10.239]ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
|
|
1131
|
[17:08:10.239]ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
|
|
1132
|
[17:08:10.239]ubi0: good PEBs: 444, bad PEBs: 0, corrupted PEBs: 0
|
|
1133
|
[17:08:10.239]ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
|
|
1134
|
[17:08:10.239]ubi0: max/mean erase counter: 4/2, WL threshold: 4096, image sequence number: 3611534910
|
|
1135
|
[17:08:10.240]ubi0: available PEBs: 0, total reserved PEBs: 444, PEBs reserved for bad PEB handling: 40
|
|
1136
|
[17:08:10.249]ubi0: background thread "ubi_bgt0d" started, PID 628
|
|
1137
|
[17:08:10.288]UBIFS (ubi0:0): Mounting in unauthenticated mode
|
|
1138
|
[17:08:10.339]UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 644
|
|
1139
|
[17:08:10.339]UBIFS (ubi0:0): recovery needed
|
|
1140
|
[17:08:10.474]UBIFS (ubi0:0): recovery completed
|
|
1141
|
[17:08:10.474]UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "app"
|
|
1142
|
[17:08:10.475]UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
|
|
1143
|
[17:08:10.475]UBIFS (ubi0:0): FS size: 49520640 bytes (47 MiB, 390 LEBs), journal size 2539520 bytes (2 MiB, 20 LEBs)
|
|
1144
|
[17:08:10.475]UBIFS (ubi0:0): reserved for root: 2338982 bytes (2284 KiB)
|
|
1145
|
[17:08:10.475]UBIFS (ubi0:0): media format: w5/r0 (latest is w5/r0), UUID FA3155A0-BDCE-47E7-B32B-650FA70D4042, small LPT model
|
|
1146
|
[17:08:10.476]mount ctc app partition !!!
|
|
1147
|
[17:08:10.520]MAXNET DPI interface Loaded
|
|
1148
|
[17:08:10.520]mouting cgroup start!
|
|
1149
|
[17:08:10.609]mouting cgroup finish!
|
|
1150
|
[17:08:10.687]random: dbus-uuidgen: uninitialized urandom read (12 bytes read)
|
|
1151
|
[17:08:10.687]random: dbus-uuidgen: uninitialized urandom read (8 bytes read)
|
|
1152
|
[17:08:10.779]random: dbus-daemon: uninitialized urandom read (12 bytes read)
|
|
1153
|
[17:08:10.812][HI_APPM] [succ] init script
|
|
1154
|
[17:08:10.812][HI_APPM] [succ] init path
|
|
1155
|
[17:08:10.812][HI_APPM] [succ] init lib
|
|
1156
|
[17:08:10.826][HI_APPM] [succ] init app
|
|
1157
|
[17:08:10.826][HI_APPM] [succ] init group
|
|
1158
|
[17:08:10.826][smart] start ipc_service !!!
|
|
1159
|
[17:08:10.870]cp: can't stat '/sbin/bpftool': No such file or directory
|
|
1160
|
[17:08:10.870][smart] wait ipc_service init fin
|
|
1161
|
[17:08:12.111][HI_IPC] ipc call hi_IPC_igdGetCmInitState_call fail, pid 2 ret 72200013, data0[6]
|
|
1162
|
[17:08:12.223][HI_APPM] [succ] init db
|
|
1163
|
[17:08:12.240][HI_APPM] [succ] new process(699)
|
|
1164
|
[17:08:12.240][HI_APPM] [succ] <0> sysinfo
|
|
1165
|
[17:08:12.251][HI_APPM] [succ] start sysinfo
|
|
1166
|
[17:08:12.251][HI_APPM] [succ] new process(701)
|
|
1167
|
[17:08:12.252][HI_APPM] [succ] <0> syslog
|
|
1168
|
[17:08:12.325][HI_APPM] [succ] <1> crashlog
|
|
1169
|
[17:08:12.325][HI_APPM] [succ] start syslog
|
|
1170
|
[17:08:12.341][HI_APPM] [succ] new process(720)
|
|
1171
|
[17:08:12.341][HI_APPM] [succ] <0> sysstat
|
|
1172
|
[17:08:13.125][HI_IPC] ipc call hi_IPC_igdGetCmInitState_call fail, pid 2 ret 72200013, data0[6]
|
|
1173
|
[17:08:13.166][HI_APPM] [succ] <1> omdiag
|
|
1174
|
[17:08:13.166][HI_APPM] [succ] start sysstat
|
|
1175
|
[17:08:13.167][HI_APPM] [succ] new process(732)
|
|
1176
|
[17:08:13.167][HI_APPM] [succ] <0> encrypt
|
|
1177
|
[17:08:13.167][HI_APPM] [succ] start encrypt
|
|
1178
|
[17:08:13.168][HI_APPM] [succ] new process(734)
|
|
1179
|
[17:08:13.173][HI_APPM] [succ] <0> board
|
|
1180
|
[17:08:13.220]
|
|
1181
|
[17:08:13.220]pon module install succ!
|
|
1182
|
[17:08:13.220]xPON CtcOam V1.0 is installed!
|
|
1183
|
[17:08:13.435]
|
|
1184
|
[17:08:13.435] hi_vendor0_bob_init ok!
|
|
1185
|
[17:08:13.435][HI_APPM] [succ] <1> bob
|
|
1186
|
[17:08:13.435][HI_APPM] [succ] <2> optical
|
|
1187
|
[17:08:13.436][HI_IPC] ipc call hi_hi_board_iomap_call_call fail, pid 734 ret 8ffffff2, data0[4]
|
|
1188
|
[17:08:13.436][HI_IPC] ipc call hi_hi_board_iomap_call_call fail, pid 734 ret 8ffffff2, data0[5]
|
|
1189
|
[17:08:13.436][HI_IPC] ipc call hi_hi_board_iomap_call_call fail, pid 734 ret 8ffffff2, data0[6]
|
|
1190
|
[17:08:13.436][HI_IPC] ipc call hi_hi_board_iomap_call_call fail, pid 734 ret 8ffffff2, data0[7]
|
|
1191
|
[17:08:13.436][HI_IPC] ipc call hi_hi_board_iomap_call_call fail, pid 734 ret 8ffffff2, data0[8]
|
|
1192
|
[17:08:13.436][HI_IPC] ipc call hi_hi_board_iomap_call_call fail, pid 734 ret 8ffffff2, data0[9]
|
|
1193
|
[17:08:13.436][HI_IPC] ipc call hi_hi_board_iomap_call_call fail, pid 734 ret 8ffffff2, data0[10]
|
|
1194
|
[17:08:13.437][HI_IPC] ipc call hi_hi_board_iomap_call_call fail, pid 734 ret 8ffffff2, data0[11]
|
|
1195
|
[17:08:13.437][HI_IPC] ipc call hi_hi_board_iomap_call_call fail, pid 734 ret 8ffffff2, data0[13]
|
|
1196
|
[17:08:13.437][HI_IPC] ipc call hi_hi_board_iomap_call_call fail, pid 734 ret 8ffffff2, data0[14]
|
|
1197
|
[17:08:13.437][LED]Led init suc!!! Led data num = 5
|
|
1198
|
[17:08:13.437][LED]Failed to open gpiochip2 err=No such file or directory
|
|
1199
|
[17:08:13.438][HI_APPM] [succ] <3> led
|
|
1200
|
[17:08:13.438][HI_IPC] ipc call hi_hi_board_iomap_call_call fail, pid 734 ret 8ffffff2, data0[19]
|
|
1201
|
[17:08:13.438][HI_IPC] ipc call hi_hi_board_iomap_call_call fail, pid 734 ret 8ffffff2, data0[19]
|
|
1202
|
[17:08:13.446][HI_APPM] [succ] <4> key
|
|
1203
|
[17:08:13.447][HI_APPM] [succ] start ext_dev
|
|
1204
|
[17:08:13.447][HI_APPM] [succ] new process(743)
|
|
1205
|
[17:08:13.491]url_init
|
|
1206
|
[17:08:13.491]
|
|
1207
|
[17:08:13.491]cfe xtables install succ!
|
|
1208
|
[17:08:14.146][HI_IPC] ipc call hi_IPC_igdGetCmInitState_call fail, pid 2 ret 72200013, data0[6]
|
|
1209
|
[17:08:14.206][WAN_ERR:hi_wan_port_attacth_netdev(334)]ifname vap20 port 20000000 not in global ports
|
|
1210
|
[17:08:14.220][WAN_ERR:hi_wan_port_attacth_netdev(334)]ifname vap50 port 40000000 not in global ports
|
|
1211
|
[17:08:14.221][WAN_ERR:hi_wan_port_attacth_netdev(334)]ifname mld2 port 80000000 not in global ports
|
|
1212
|
[17:08:15.140][HI_IPC] ipc call hi_IPC_igdGetCmInitState_call fail, pid 2 ret 72200013, data0[6]
|
|
1213
|
[17:08:15.704][HI_APPM] [succ] <0> wan
|
|
1214
|
[17:08:15.738]insmod ra_bind succ!!
|
|
1215
|
[17:08:15.966]lan init succ
|
|
1216
|
[17:08:15.966][HI_APPM] [succ] <1> lan
|
|
1217
|
[17:08:15.966]insmod vxlan succ!!
|
|
1218
|
[17:08:16.054][HI_APPM] [succ] <2> vxlan
|
|
1219
|
[17:08:16.073][HI_APPM] [succ] start wan_lan
|
|
1220
|
[17:08:16.073][HI_APPM] [succ] new process(1064)
|
|
1221
|
[17:08:16.082][HI_APPM] [succ] <0> wlan
|
|
1222
|
[17:08:16.142][HI_IPC] ipc call hi_IPC_igdGetCmInitState_call fail, pid 2 ret 72200013, data0[6]
|
|
1223
|
[17:08:16.142]insmod hostlimit succ!!
|
|
1224
|
[17:08:16.398][HI_APPM] [succ] <1> lanhost
|
|
1225
|
[17:08:16.399][HI_APPM] [succ] start host
|
|
1226
|
[17:08:16.414][HI_APPM] [succ] new process(1108)
|
|
1227
|
[17:08:16.414]hi_qos_init ui_nf_conntrack_max= 61000
|
|
1228
|
[17:08:17.156][HI_IPC] ipc call hi_IPC_igdGetCmInitState_call fail, pid 2 ret 72200013, data0[6]
|
|
1229
|
[17:08:17.671][HI_APPM] [succ] <0random: fast init done
|
|
1230
|
[17:08:17.671]> qos
|
|
1231
|
[17:08:17.671][HI_APPM] [succ] start qos
|
|
1232
|
[17:08:17.687][HI_APPM] [succ] new process(1264)
|
|
1233
|
[17:08:18.152][HI_IPC] ipc call hi_IPC_igdGetCmInitState_call fail, pid 2 ret 72200013, data0[6]
|
|
1234
|
[17:08:18.477][HI_IPC] ipc call hi_hi_vpn_check_tunn_name_call fail, pid 0 ret 72200013, data0[812151909]
|
|
1235
|
[17:08:18.486][HI_IPC] ipc call hi_hi_vpn_check_tunn_name_call fail, pid 0 ret 72200013, data0[812151909]
|
|
1236
|
[17:08:19.031][HI_APPM] [succ] <0> sec
|
|
1237
|
[17:08:19.155][HI_IPC] ipc call hi_IPC_igdGetCmInitState_call fail, pid 2 ret 72200013, data0[6]
|
|
1238
|
[17:08:20.148][HI_IPC] ipc call hi_IPC_igdGetCmInitState_call fail, pid 2 ret 72200013, data0[6]
|
|
1239
|
[17:08:20.391][HI_APPM] [succ] <1> netapp
|
|
1240
|
[17:08:20.401][HI_APPM] [succ] <2> emu
|
|
1241
|
[17:08:20.401][HI_APPM] [succ] start netapp
|
|
1242
|
[17:08:20.423][HI_APPM] [succ] new process(1423)
|
|
1243
|
[17:08:20.646][HI_APPM] [succ] <0> vpn
|
|
1244
|
[17:08:20.646][HI_APPM] [succ] <1> upgrade
|
|
1245
|
[17:08:20.646][HI_APPM] [succ] <2> download
|
|
1246
|
[17:08:20.647][HI_APPM] [succ] <3> upload
|
|
1247
|
[17:08:20.647][HI_APPM] [succ] start netservice
|
|
1248
|
[17:08:20.667][HI_APPM] [succ] new process(1437)
|
|
1249
|
[17:08:20.667][HI_APPM] [succ] <0> voip
|
|
1250
|
[17:08:20.667][HI_APPM] [succ] <1> slic
|
|
1251
|
[17:08:21.011]
|
|
1252
|
[17:08:21.011]hisilicon kvoip module install succ!
|
|
1253
|
[17:08:21.160][HI_IPC] ipc call hi_IPC_igdGetCmInitState_call fail, pid 2 ret 72200013, data0[6]
|
|
1254
|
[17:08:21.222]zsp_min.out
|
|
1255
|
[17:08:21.330][HI_APPM] [succ] <2> voice
|
|
1256
|
[17:08:21.331][HI_APPM] [succ] <3> vtest
|
|
1257
|
[17:08:21.331][HI_APPM] [succ] start voice
|
|
1258
|
[17:08:21.331][HI_APPM] [succ] new process(1476)
|
|
1259
|
[17:08:21.332][HI_APPM] [succ] <0> sml
|
|
1260
|
[17:08:21.332][HI_APPM] [succ] start sml
|
|
1261
|
[17:08:21.340][HI_APPM] [succ] new process(1478)
|
|
1262
|
[17:08:21.340][HI_APPM] [succ] <0> omci_tapi
|
|
1263
|
[17:08:21.439][HI_APPM] [succ] <1> omci_sql
|
|
1264
|
[17:08:21.439][HI_APPM] [succ] <2> omci_ctl
|
|
1265
|
[17:08:21.443][HI_APPM] [succ] <3> oam
|
|
1266
|
[17:08:21.465][HI_APPM] [succ] <4> auto_sensing_ad
|
|
1267
|
[17:08:21.465][HI_APPM] [succ] <5> auto_sensing
|
|
1268
|
[17:08:21.472][HI_APPM] [succ] start cms
|
|
1269
|
[17:08:21.472][HI_APPM] [succ] new process(1480)
|
|
1270
|
[17:08:21.517]#Init cm moudle#
|
|
1271
|
[17:08:21.563]# Load CM config file#
|
|
1272
|
[17:08:21.670]Config_parser Succ.
|
|
1273
|
[17:08:21.670]Load Config from config file Succ.
|
|
1274
|
[17:08:21.670]Config load Succ!
|
|
1275
|
[17:08:21.670]############ Start Distribute CM Config data ############
|
|
1276
|
[17:08:21.670][sysuptime: 23] Distribute Early!
|
|
1277
|
[17:08:21.670]sendIPCServiceMsg: msgget failed errno=2 No such file or directory, type 1200
|
|
1278
|
[17:08:21.685]sendIPCServiceMsg: msgget failed errno=2 No such file or directory, type 1200
|
|
1279
|
[17:08:21.738][HI_APPM] [succ] <0> odl
|
|
1280
|
[17:08:21.739][HI_APPM] [succ] start cm
|
|
1281
|
[17:08:21.758][HI_APPM] [succ] new process(1504)
|
|
1282
|
[17:08:21.969][HI_APPM] [succ] <0> cwmp
|
|
1283
|
[17:08:21.983][HI_APPM] [succ] start cwmp
|
|
1284
|
[17:08:21.984][HI_APPM] [succ] init env
|
|
1285
|
[17:08:21.984][HI_APPM] [succ] init cmd
|
|
1286
|
[17:08:22.001][HI_APPM] [succ] init monitor
|
|
1287
|
[17:08:22.001][HI_APPM] ########### Appm Start End ###########
|
|
1288
|
[17:08:22.504][sysuptime: 23] Start init cm remote management module!
|
|
1289
|
[17:08:22.524]sendIPCServiceMsg: msgget failed errno=2 No such file or directory, type 1200
|
|
1290
|
[17:08:22.524]LOS ALARM CLEAR
|
|
1291
|
[17:08:22.524]
|
|
1292
|
[17:08:22.524][STDOAM]LLID(0) O1>>>O2
|
|
1293
|
[17:08:22.524]
|
|
1294
|
[17:08:22.524]Init CTC OAM SUCC!
|
|
1295
|
[17:08:22.586]start epon regist, loid=XEPON4309, lopwd=1234
|
|
1296
|
[17:08:22.587]save_uplink_reg_loid XEPON4309 lopwd 1234
|
|
1297
|
[17:08:22.997][ctc_regstatus_proc:2550] LOID Register 20
|
|
1298
|
[17:08:23.159]udhcpc: started, v1.27.2
|
|
1299
|
[17:08:23.178][May 12 2025-11:22:18], Receive Wan Connection Down Event, WanName [1_TR069_R_VID_46].
|
|
1300
|
[17:08:23.194]sendIPCServiceMsg: msgget failed errno=2 No such file or directory, type 1200
|
|
1301
|
[17:08:23.195]sendIPCServiceMsg: msgget failed errno=2 No such file or directory, type 1223
|
|
1302
|
[17:08:23.251]udhcpc: [1970-01-01 08:00:24.730] sending discover
|
|
1303
|
[17:08:23.284][May 12 2025-11:22:18], Receive Wan Connection Down Event, WanName [1_TR069_R_VID_46].
|
|
1304
|
[17:08:23.298]sendIPCServiceMsg: msgget failed errno=2 No such file or directory, type 1200
|
|
1305
|
[17:08:23.298]sendIPCServiceMsg: msgget failed errno=2 No such file or directory, type 1223
|
|
1306
|
[17:08:23.475]
|
|
1307
|
[17:08:23.483] error=0x7000000e function=__qos_wan_mixapp_add line=889
|
|
1308
|
[17:08:23.491][May 12 2025-11:22:18], Receive Wan Connection Add Event, WanName [1_TR069_R_VID_46].
|
|
1309
|
[17:08:23.552]killall: phddns: no process killed
|
|
1310
|
[17:08:23.808][sysuptime: 25] Distribute Main!
|
|
1311
|
[17:08:23.882]sendIPCServiceMsg: msgget failed errno=2 No such file or directory, type 1200
|
|
1312
|
[17:08:26.555][sysuptime: 28] Distribute Medium!
|
|
1313
|
[17:08:26.555]run easymesh daemon
|
|
1314
|
[17:08:27.633][MPCP]LLID(0): O1 => O2
|
|
1315
|
[17:08:27.663]
|
|
1316
|
[17:08:27.663] MPCP llid(0) reg state : 1
|
|
1317
|
[17:08:27.664]iLOS ALARM CLEAR
|
|
1318
|
[17:08:27.664]nit oam llid(0)
|
|
1319
|
[17:08:27.664]
|
|
1320
|
[17:08:27.664][STDOAM]LLID(0) O1>>>O2
|
|
1321
|
[17:08:27.664]
|
|
1322
|
[17:08:27.664]Init CTC OAM SUCC!
|
|
1323
|
[17:08:28.569]nf_conntrack_rtsp v0.7 loading
|
|
1324
|
[17:08:28.569]nf_nat_rtsp v0.7 loading
|
|
1325
|
[17:08:28.962]sendIPCServiceMsg: msgget failed errno=2 No such file or directory, type 1233
|
|
1326
|
[17:08:29.457][MPCP]LLID(0): O2 => O3
|
|
1327
|
[17:08:29.457]
|
|
1328
|
[17:08:29.457] MPCP llid(0) reg state : 2
|
|
1329
|
[17:08:29.541]
|
|
1330
|
[17:08:29.541][STDOAM]LLID(0) O2>>>O3
|
|
1331
|
[17:08:29.541]
|
|
1332
|
[17:08:29.542][STDOAM]LLID(0) O3>>>O4
|
|
1333
|
[17:08:29.542]
|
|
1334
|
[17:08:29.542][CTCOAM]LLID(0) O1>>>O2
|
|
1335
|
[17:08:29.542]
|
|
1336
|
[17:08:29.542] ctcoam llid(0) reg state : 1
|
|
1337
|
[17:08:29.542][CTCOAM]LLID(0) O2>>>O3
|
|
1338
|
[17:08:29.542]
|
|
1339
|
[17:08:29.542]
|
|
1340
|
[17:08:29.542] ctcoam llid(0) reg state :
|
|
1341
|
[17:08:29.542][CTCOAM]LLID(0) O3>>>O4
|
|
1342
|
[17:08:29.542] 2
|
|
1343
|
[17:08:29.542]
|
|
1344
|
[17:08:29.542][EPON]LLID(0) Online!
|
|
1345
|
[17:08:29.542]
|
|
1346
|
[17:08:29.550] ctcoam llid(0) reg state : 3
|
|
1347
|
[17:08:30.052]chpasswd: password for 'telnetadmin_telnet' changed
|
|
1348
|
[17:08:30.052]TELNET_ENABLE: 1 TELNET_PORT: 23 TELNET_WAN_PORT: 23
|
|
1349
|
[17:08:30.062]killall: telnetd: no process killed
|
|
1350
|
[17:08:30.136]FTP_ENABLE: 0 FTP_PORT: 21 FTP_ANONYMOUS: NO FTP_USER: 12345_ftp FTP_IP: 192.168.1.1 FTP_WAN:null
|
|
1351
|
[17:08:30.138]killall: vsftpd: no process killed
|
|
1352
|
[17:08:30.138]sed: /tmp/etc/vsftpd/user_list: No such file or directory
|
|
1353
|
[17:08:30.138]chown: /tmp/etc/vsftpd.conf: No such file or directory
|
|
1354
|
[17:08:30.138]chown: /tmp/etc/vsftpd_wan.conf: No such file or directory
|
|
1355
|
[17:08:30.138]chown: /tmp/etc/vsftpd/user_list: No such file or directory
|
|
1356
|
[17:08:30.155]SSH_ENABLE: 0 SSH_USER: SSH_PASSWD: SSH_PORT:
|
|
1357
|
[17:08:30.155]killall: dropbear: no process killed
|
|
1358
|
[17:08:30.415]urandom_read: 1 callbacks suppressed
|
|
1359
|
[17:08:30.416]random: dnsmasq: uninitialized urandom read (128 bytes read)
|
|
1360
|
[17:08:30.426]__!!!!!!!_Service_Num=1 g_Servicrandom: dnsmasq: uninitialized urandom read (48 bytes read)
|
|
1361
|
[17:08:30.432]e_Name=VOIP
|
|
1362
|
[17:08:30.755]__!!!!!!!_Service_Num=1 g_Service_Name=VOIP
|
|
1363
|
[17:08:30.982]
|
|
1364
|
[17:08:31.219]Login: sendIPCServiceMsg: msgget failed errno=2 No such file or directory, type 1200
|
|
1365
|
[17:08:31.219][sysuptime: 32] Distribute Tardy!
|
|
1366
|
[17:08:31.235]ulIPver: 0 ulPingCnt: 4 ulBlkSize: 56 ulTimeout: 10000 ulInterval: 0 acWanIf: acHost:
|
|
1367
|
[17:08:31.236]pc_waninterface:
|
|
1368
|
[17:08:31.236]ifname: host:
|
|
1369
|
[17:08:31.236]___pIgdPMUsbGlobalCfgAttrTab->ucUsbShare=0
|
|
1370
|
[17:08:31.398]CM RepNum: 5
|
|
1371
|
[17:08:31.429]INFO [HI_EmAgentApiInit:432]HI_EmAgentApiInit success
|
|
1372
|
[17:08:31.430][XML_WRN:_mib_chain_get(243)] recordNum(0), id(607), final_idx(0), pCurr(0), pCurr->pData(0)
|
|
1373
|
[17:08:31.793][XML_WRN:_mib_chain_get(243)] recordNum(0), id(747), final_idx(1), pCurr(0), pCurr->pData(0)
|
|
1374
|
[17:08:31.804][sysuptime: 33] Distribute Finish!
|
|
1375
|
[17:08:32.030]*************ipc_service main**************
|
|
1376
|
[17:08:32.031]
|
|
1377
|
[17:08:32.031]ipc_service init start!
|
|
1378
|
[17:08:32.031]#####Oprator:1, Area:0 PonRegType: 0####
|
|
1379
|
[17:08:32.091][HI_IPC] ipc call hi_IPC_igdCmConfGetallIndex_call fail, pid 1480 ret 72200008, data0[0]
|
|
1380
|
[17:08:32.105][HI_IPC] ipc call hi_IPC_igdCmConfGetallIndex_call fail, pid 1480 ret 72200008, data0[0]
|
|
1381
|
[17:08:32.163][HI_IPC] ipc call hi_IPC_igdCmConfGetallIndex_call fail, pid 1480 ret 72200008, data0[0]
|
|
1382
|
[17:08:32.255]Start webserver now
|
|
1383
|
[17:08:32.255]g_ssidnum_band[0]=0
|
|
1384
|
[17:08:32.255]g_ssidnum_band[1]=0
|
|
1385
|
[17:08:32.283][HI_IPC] ipc call hi_IPC_igdCmConfGetallIndex_call fail, pid 1480 ret 72200008, data0[0]
|
|
1386
|
[17:08:32.284]ipc_service conn init succ!
|
|
1387
|
[17:08:32.300]ipc_service update proc init!
|
|
1388
|
[17:08:32.300]ipc_service init finished!
|
|
1389
|
[17:08:33.030][smart] ipc_service finish, start smart firmware !!!
|
|
1390
|
[17:08:33.117][smart] start smart firmware finish
|
|
1391
|
[17:08:33.146]en : 0x1
|
|
1392
|
[17:08:33.147]chk_time : 0x1
|
|
1393
|
[17:08:33.147]wait_time : 0x5
|
|
1394
|
[17:08:33.147]los_cnt : 0x5
|
|
1395
|
[17:08:33.147]reg_check_time : 0xf
|
|
1396
|
[17:08:33.147]succ.
|
|
1397
|
[17:08:33.181]saf_add_masquerade_rule 4148
|
|
1398
|
[17:08:33.239]udhcpc: [1970-01-01 08:00:34.700] sending discover
|
|
1399
|
[17:08:33.559]mount: can't read '/etc/fstab': No such file or directory
|
|
1400
|
[17:08:33.662]cgroup: saf (2319) created nested cgroup for controller "memory" which has incomplete hierarchy support. Nested cgroups may change behavior in the future.
|
|
1401
|
[17:08:33.685]cgroup: "memory" requires setting use_hierarchy to 1 on the root
|
|
1402
|
[17:08:34.346]udhcpc: received SIGTERM
|
|
1403
|
[17:08:34.346]udhcpc: entering released state
|
|
1404
|
[17:08:34.406][May 12 2025-11:22:18][sysuptime: 35], Receive PON Up Event.
|
|
1405
|
[17:08:34.483]udhcpc: started, v1.27.2
|
|
1406
|
[17:08:34.483][May 12 2025-11:22:18], Receive Wan Connection Down Event, WanName [1_TR069_R_VID_46].
|
|
1407
|
[17:08:34.574]udhcpc: [1970-01-01 08:00:36.040] sending discover
|
|
1408
|
[17:08:38.922]random: ubusd: uninitialized urandom read (4 bytes read)
|
|
1409
|
[17:08:38.922]random: ubusd: uninitialized urandom read (4 bytes read)
|
|
1410
|
[17:08:38.936]random: ubusd: uninitialized urandom read (4 bytes read)
|
|
1411
|
[17:08:39.782][ctc_regstatus_proc:2558] LOID Register 30
|
|
1412
|
[17:08:44.524]udhcpc: [1970-01-01 08:00:46.003] sending discover
|
|
1413
|
[17:08:45.216]iptables: No chain/target/match by that name.
|
|
1414
|
[17:08:45.272]iptables v1.8.2 (legacy): Couldn't load target `ct_redict_dnat':No such file or directory
|
|
1415
|
[17:08:45.276]
|
|
1416
|
[17:08:45.276]Try `iptables -h' or 'iptables --help' for more information.
|
|
1417
|
[17:08:45.276]iptables: No chain/target/match by that name.
|
|
1418
|
[17:08:45.276]sipapp started, File: /home/ply/hsan/gateway/service/voice/adpt/src/voip_api.c, Line: 5887, Function: VOIP_start_app_thread !
|
|
1419
|
[17:08:45.277]iptables: No chain/target/match by that name.
|
|
1420
|
[17:08:45.277]iptables v1.8.2 (legacy): Couldn't load target `ct_redict_reject':No such file or directory
|
|
1421
|
[17:08:45.278]
|
|
1422
|
[17:08:45.292]Try `iptables -h' or 'iptables --help' for more information.
|
|
1423
|
[17:08:45.292]iptables: No chain/target/match by that name.
|
|
1424
|
[17:08:46.381]memshr init OK
|
|
1425
|
[17:08:46.381]ctSgw_appRegisterFunc: 250 (ptrval)/(ptrval)/00000000
|
|
1426
|
[17:08:46.382]ctSgw_appRegisterForwardProc: 775, prio -190
|
|
1427
|
[17:08:46.400]xmit pkt api does not support
|
|
1428
|
[17:08:46.401]this is the kernel b01 loaded by m01-b01
|
|
1429
|
[17:08:47.341]Init DSP starting...
|
|
1430
|
[17:08:47.342]ASIC Init begin
|
|
1431
|
[17:08:47.342]LoadZspCode Success, waiting for bootting...
|
|
1432
|
[17:08:47.342]zsp_boot Success!
|
|
1433
|
[17:08:47.342]ASIC Init end
|
|
1434
|
[17:08:47.352]Init DSP OK!
|
|
1435
|
[17:08:47.763]random: crng init done
|
|
1436
|
[17:08:47.763]random: 1 urandom warning(s) missed due to ratelimiting
|
|
1437
|
[17:08:51.779]###########critical_process_check,485############
|
|
1438
|
[17:08:51.780]###########critical_process_check,485############
|
|
1439
|
[17:08:51.828]###########critical_process_check,485############
|
|
1440
|
[17:08:54.459]udhcpc: [1970-01-01 08:00:55.930] sending discover
|
|
1441
|
[17:08:56.271]20250516-170856.271
|
|
1442
|
[17:08:56.390]20250516-170856.390
|